Aerpro AMHJP2K Скачать руководство пользователя страница 3

Страница: 3 / 14

Aerpro AERA10

Radio Replacement Kit

for Jeep

Wrangler JL and Jeep Gladiator JT Vehicles

AMHJP2

Page 3

Step 3

Step 2

Step 1

NOTE: LEFT HAND DRIVE VEHICLE PICTURE

FOR ILLUSTRATION PURPOSES ONLY

Section 1: Disassembly

Part One: Radio Removal

Disconnect the push-to-start button

and climate control connectors

from the back of the climate control

panel and remove.

Grasp the climate control panel at

the exposed left edge and pull out

to unclip the left side, then work

your fingers around the remaining

edges of the panel to fully unclip it.

Pull out at the top of the knee

bolster to release the retaining

clips, then work your hands down

the edges of the knee bolster to

release the remaining clips and

remove the panel.

Step 6

Step 5

Step 4

Disconnect the antenna and USB

connectors from the back of the

radio, then disconnect the 52-

pin dock-and-lock connector and

remove the radio.

Remove the four 7mm screws

securing the radio in place, then

lift the radio out of the radio

cavity.

Remove the two 7mm screws

securing the radio bezel to the

dash, then pull outward on

the radio bezel to unclip it and

remove.

This installation manual will cover the necessary order of procedures to complete the installation

efficiently and to avoid redoing any steps along the way. The order will be as follows; Disassembly,

Radio Unit Mounting Preparation, Radio Unit Harness Connections and Preparation, In-Vehicle Harness

Connections and Preparation, Radio Unit Installation, and Reassembly.

Содержание AMHJP2K















Результаты поиска

Содержание AMHJP2K

Отзывы:

Бренды по названию

Популярные бренды

Aerpro AMHJP2K, Руководство пользователя

Результаты поиска

Содержание AMHJP2K

Отзывы:

Бренды по названию

Популярные бренды