Aerpro AMHJP2K Скачать руководство пользователя страница 6

Страница: 6 / 14

Aerpro AERA10

Radio Replacement Kit

for Jeep

Wrangler JL and Jeep Gladiator JT Vehicles

AMHJP2

Page 6

Section 2: Radio Unit Mounting Preparation

Step 2

Step 1

Secure the side brackets to

the main bracket using the four

#10x3/8 Phillips course threaded

screws.

Slide the left and right side

brackets (marked by the letters

LH and RH) into the back of the

main bracket (the orientation of

the main bracket is marked by the

part number at the top).

Step 3

Step 2

Step 1

Mount the

AERA10D

radio module

onto the side brackets using the four

M5x10 Phillips screws (only two

shown). Ensure that the ports for

connections on the radio module are

facing down.

Mount the PAC-LINK module to

the lower part of the CH4A-JW18

module using a piece of the

provided double-sided tape.

Mount the CH4A-JW18 module to

the left and right inner mounting

tabs of the radio module

mounting brackets using zip ties.

Ensure the module is oriented

with the part number (CH4A-

JW18) on the right side.

Part One: Assembling the Radio Module Mounting Brackets

Part Two: Mounting the Interface Modules and

AERA10D

Radio Module

Note: It does not matter what the DIP switches on the

CH4A-JW18 module are set to.

Содержание AMHJP2K















Результаты поиска

Содержание AMHJP2K

Отзывы:

Бренды по названию

Популярные бренды

Aerpro AMHJP2K, Руководство пользователя

Результаты поиска

Содержание AMHJP2K

Отзывы:

Бренды по названию

Популярные бренды