Aerpro AMHJP2K Скачать руководство пользователя страница 13

Страница: 13 / 14

Aerpro AERA10

Radio Replacement Kit

for Jeep

Wrangler JL and Jeep Gladiator JT Vehicles

AMHJP2

Page 13

Section 5: Radio Unit Installation (cont.)

Part One: Harness and Cabling Connections (cont.)

Step 4

Connect the 10P-2-10P-18

connector coming from the RPA-

HD1 interface module into the

open port on the PL1 interface

module, then connect the 52-pin

dock-and-lock connector to the

main OEM radio connector in the

vehicle.

For a complete wiring diagram overview, refer to page 2.

Part Two: Radio Unit Mounting

Step 2

Step 1

Connect the

AERA10D

display

cables into the back of the

AERA10D

radio display and

secure it to the radio unit

mounting bracket against the

dash using the orange clips and

the two 7mm screws below the

radio cavity.

While holding the cabling above

the vents in the dash, slide the

radio unit into the radio cavity and

secure it to the dash using the

four 7mm screws that held the

factory radio in place.

Note: Once the radio unit is

slid into the radio cavity, the kit

will not always seat fully into

the dash. There is sometimes

about a 1/4-inch gap between

the screw holes. If the previous

steps of the instructions were

followed, this 1/4-inch gap will

close with the tightening of the

four 7mm screws, allowing the kit

to seat fully into place. If there is

more than a 1/4-inch gap before

installing the screws, slide the

radio unit back out and readjust

the connectors and cables behind

the radio opening until they are no

longer in the way of the radio unit,

then reinstall.

Gray

USB-UN1

adapter cable

Black center console

USB-UN2

adapter cable

Connect the USBs into the

appropriate ports on the

AERA10D

radio module. Ensure

that the USB-UN1 is connected to

port 1, and the center console

USB-UN2 is connected to port 2.

Step 5

Connect the AM/FM antenna (3),

the HDMI cable (4), and the GPS

antenna (5).

Step 6

Содержание AMHJP2K















Результаты поиска

Содержание AMHJP2K

Отзывы:

Бренды по названию

Популярные бренды

Aerpro AMHJP2K, Руководство пользователя

Результаты поиска

Содержание AMHJP2K

Отзывы:

Бренды по названию

Популярные бренды