Aerotech Automation1 XI4-4P1 Скачать руководство пользователя страница 29

Страница: 29 / 78

1.3. Environmental Specifications

The environmental specifications are listed below.

Table 1-6:

Environmental Specifications

Ambient
Temperature

Operating: 0° to 40°C (32° to 104° F)
Storage: -30° to 85°C (-22° to 185° F)

Humidity
Non-condensing

The maximum relative humidity is 80% for temperatures that are
less than 31°C and decreases linearly to 50% relative humidity at
40°C.

Operating Altitude

0 m to 2,000 m (0 ft to 6,562 ft) above sea level.
If you must operate this product above 2,000 m or below sea level,
contact Aerotech, Inc.

Pollution

Pollution Degree 2
Typically only nonconductive pollution occurs.

Operation

Use only indoors

1.4. Drive and Software Compatibility

This table shows the available drives and which version of the software first supported each drive. In
the

Last Software Version

column, drives that show a specific version number are not supported

after that version.

Table 1-7:

Drive and Software Compatibility

Drive Type

First Software Version

Last Software Version

iXI4

2.2.0

Current

XI4

2.1.0

Current

iXI4/XI4 Hardware Manual

1.3. Environmental Specifications

www.aerotech.com

Содержание Automation1 XI4-4P1















































































Результаты поиска

Содержание Automation1 XI4-4P1

Отзывы:

Похожие инструкции для Automation1 XI4-4P1

Бренды по названию

Популярные бренды

Aerotech Automation1 XI4-4P1, Руководство по оборудованию

Результаты поиска

Содержание Automation1 XI4-4P1

Отзывы:

Похожие инструкции для Automation1 XI4-4P1

Бренды по названию

Популярные бренды