Aerotech Automation1 XI4-4P1 Скачать руководство пользователя страница 27

Страница: 27 / 78

1.2.3. DIN Rail Mounting

A DIN rail can only be used with the -2P1 or -4P1 options.

DIN Rail Mounting Procedure:

1. Mount the DIN rail clip to the iXI4/XI4. The clip and #6-32 x 1/4 flat head screws are included in

the DIN rail clip kit.

2. Cut the DIN rail so one complete mounting hole extends beyond the last component at each end.
3. Secure the DIN Rail to the mounting surface with #10-32 screws spaced every six inches.

NOTE: Do not install the DIN rail to the mounting surface with the components already attached.

4. Install all components on to the DIN rail.

Table 1-4:

Mounting Parts

Aerotech P/N

DIN Rail

EAM00914

DIN Rail Clip Kit

HyperWire-DIN

Figure 1-10:

Din Rail Clip Dimensions

iXI4/XI4 Hardware Manual

1.2.3. DIN Rail Mounting

www.aerotech.com

Содержание Automation1 XI4-4P1















































































Результаты поиска

Содержание Automation1 XI4-4P1

Отзывы:

Похожие инструкции для Automation1 XI4-4P1

Бренды по названию

Популярные бренды

Aerotech Automation1 XI4-4P1, Руководство по оборудованию

Результаты поиска

Содержание Automation1 XI4-4P1

Отзывы:

Похожие инструкции для Automation1 XI4-4P1

Бренды по названию

Популярные бренды