Advantech PPC-102 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 126

background image

iii

Packing List

Before installing your panel PC, ensure that the following materials have
been received:

• PPC-102 series panel PC
• User's manual
• Accessories for PPC-102

- Power cable for both FDD and HDD/CD-ROM
- FDD flat cable (35 cm)
- Keyboard extension cable (5-pin DIN female to 6-pin PS/2 male)
- FDD power cable
- HDD flat cable (44-pin) (5 cm)
- HDD flat cable (40-pin) (46 cm)
- Line-in cable
- Power cord (1.8 m) - USA type
- Assembly mounting parts
- Heat sink
- HDD bracket
- Utility disks
- Screws

If any of these items are missing or damaged, contact your distributor or
sales representative immediately.

Note:

1. The heat sink is included in the PPC-102's accessory box.

2. The CPU you intend to purchase may be sold together with a fan

attached with adhesive.

3. Customers must buy the CPU separately. Do not buy a CPU that

already has a fan attached with adhesive, because it is not easy to
remove such fan.

If you install a 586 series CPU yourself, you must install a heat sink above
the CPU in order to avoid heat damage to the CPU. The CPU and the heat
sink are normally sold together with the fan attached to the CPU. Due to
tight constraints within the PPC-102’s housing, care must be taken to use
the heat sink in the accessory box which will both cool the CPU and fit
within the PPC-102. Thus you must buy a CPU without a fan attached.

«
1
2
3
4
5
...
»

Содержание PPC-102































































































































Отзывы:

Нет отзывов

Похожие инструкции для PPC-102

Бренд: Zenith Страницы: 493

Бренд: TechNexion Страницы: 37

Бренд: C&T Solution Страницы: 108

Бренд: eMachines Страницы: 46

Бренд: Magic Страницы: 19

Height Adjustable Standing Desk 4-Leg

Бренд: Uplift Desk Страницы: 7

Бренд: Asus Страницы: 80

Бренд: Asus Страницы: 35

Бренд: Asus Страницы: 56

Бренд: Asus Страницы: 35

Бренд: Asus Страницы: 69

Бренд: Asus Страницы: 28

Бренд: Asus Страницы: 28

Бренд: Asus Страницы: 35

Бренд: Asus Страницы: 2

Chromebox CN Series

Бренд: Asus Страницы: 34

Бренд: Asus Страницы: 2

Бренд: Asus Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды