Advantech EKI-7556MI Скачать руководство пользователя | Manualshive

Страница: 49 / 105

background image

The interface allows users to configure the switch to receive an IP address from DHCP server or
manually fill in

IP Address

,

Subnet Mask

,

Gateway

, IP addresses of the primary and the secondary

DNS servers.

•

DHCP Client

: Enable or disable the DHCP client function. When DHCP client function is enabled, the

industrial switch will be assigned an IP address from the network DHCP server. The default IP
address will be replaced by the assigned IP address on DHCP server. After users click

Apply

, a

popup dialog shows up. It is to inform the user that when the DHCP client is enabled, the current IP
will lose and user should find the new IP on the DHCP server.

•

IP Address

: Assign the IP address that the network is using. If DHCP client function is enabled, and

then the user doesn’t need to assign the IP address. And, the network DHCP server will assign the IP
address displaying in this column for the industrial switch. The default IP is 192.168.1.1.

•

Subnet Mask

: Assign the subnet mask to the IP address. If DHCP client function is enabled, and

then the user does not need to assign the subnet mask.

•

Gateway

: Assign the network gateway for the industrial switch. The default gateway is 192.168.1.254.

•

DNS1

: The abbreviation of Domain Name Server—an Internet service that translate domain name

into IP addresses. Domain name are alphabetic which are easy to be remembered. Because the
Internet is based on IP address; every time you use a domain name, therefore, a DNS service must
translate the name into the corresponding IP address. For example, the domain name

www.net.com

might translate to 192.168.1.1

•

DNS2

: The backup for DNS1. When DNS1 cannot function, DNS2 will then replace DNS1

immediately.

•

And then, click

Apply

.

Figure 3.3-5

IP Configuration

49

Chapter3

«
...
47
48
49
50
51
...
»

Содержание EKI-7556MI










































































































Отзывы:

Нет отзывов

Похожие инструкции для EKI-7556MI

Бренд: D-Link Страницы: 99

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 15

AirPro DWL-6000AP

Бренд: D-Link Страницы: 65

Бренд: D-Linke Страницы: 32

Бренд: National Instruments Страницы: 36

Бренд: Parkside Страницы: 55

Бренд: Parkside Страницы: 34

ZyXEL EES-1024AF

Бренд: ZyXEL Communications Страницы: 99

Бренд: Lorex Страницы: 186

Бренд: Lanner Страницы: 78

Бренд: Juniper Страницы: 190

Бренд: Garderos Страницы: 23

Бренд: Patton electronics Страницы: 9

Бренд: Qlogic Страницы: 8

Бренд: Gira Страницы: 6

Octopus G Series

Бренд: TwinMOS Страницы: 29

JetNet 3508-LVDC

Бренд: Korenix Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды