Advantech EKI-7556MI Скачать руководство пользователя страница 17

Страница: 17 / 105

Chapter 2

Installation

In this chapter, you will be given an overview of the EKI-7556MI hardware installation procedures.

2.1 LED

Indicators

There are some LEDs located on the front panel display the power status and network status of EKI-
7556MI. Each of them has its own specific meaning shown as below.

Table 2.1: EKI-7556MI LED Definition

LED Color

Description

System power on

PWR Green

Off

No power input

The industrial switch is the master of the X-ring group

R.M. Green

Off

The industrial switch is not the master of the X-ring group

Power input 1 is active

PWR1 Green

Off

Power input 1 is inactive

Power input 2 is active

PWR2 Green

Off

Power input 2 is inactive

Power input 1 or 2 is inactive or port link down
(depends on Fault Relay Alarm configuration)

P-Fail Red

Off

Power input 1 and 2 are both active, or no power input

SFP port is linking

Flashing

Data is transmitting or receiving

Link/Active
(17,18)

Green

Off

Not connected to network

Connected to network

Flashing

Networking is active

Link/Active
(1~16)

Green

Off

Not connected to network

Ethernet port full duplex

Flashing

Collision of packets occurs

Duplex/Collision
(1~16)

Orange

Off

Ethernet port half duplex or not connected to network

17 Chapter2

Содержание EKI-7556MI










































































































Результаты поиска

Содержание EKI-7556MI

Отзывы:

Advantech EKI-7556MI, Руководство пользователя, Страница: 17 / 105

Результаты поиска

Содержание EKI-7556MI

Отзывы: