Advantech EKI-7556MI Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 105

Advantech EKI-7556MI Скачать руководство пользователя страница 39

spanning-tree priority

[0~61440]

G

Configure spanning tree priority
parameter

switch(config)#

spanning-tree priority 32767

spanning-tree max-age

[seconds]

G

Use the spanning-tree max-age
global configuration command to
change the interval between
messages the spanning tree
receives from the root switch. If a
switch does not receive a bridge
protocol data unit (BPDU)
message from the root switch
within this interval, it recomputed
the Spanning Tree Protocol (STP)
topology.

switch(config)#

spanning-tree max-age 15

spanning-tree hello-time

[seconds]

G

Use the spanning-tree hello-time
global configuration command to
specify the interval between hello
bridge protocol data units
(BPDUs).

switch(config)#

spanning-tree hello-time 3

spanning-tree forward-time

[seconds]

G

Use the spanning-tree forward-
time global configuration command
to set the forwarding-time for the
specified spanning-tree instances.
The forwarding time determines
how long each of the listening and
learning states last before the port
begins forwarding.

switch(config)#

spanning-tree forward-time 20

stp-path-cost

[1~200000000]

I

Use the spanning-tree cost
interface configuration command
to set the path cost for Spanning
Tree
Protocol (STP) calculations. In the
event of a loop, spanning tree
considers the path cost when
selecting
an interface to place into the
forwarding state.

switch(config)#

interface fastEthernet 2

switch(config-if)#

stp-path-cost 20

stp-path-priority

[Port Priority]

I

Use the spanning-tree port-priority
interface configuration command
to configure a port priority that
is used when two switches tie for
position as the root switch.

switch(config)#

interface fastEthernet 2

switch(config-if)#

stp-path-priority 128

stp-admin-p2p

[Auto|True|False]

I

Admin P2P of STP priority on this
interface.

switch(config)#

interface fastEthernet 2

switch(config-if)#

stp-admin-p2p Auto

stp-admin-edge

[True|False]

I

Admin Edge of STP priority on this
interface.

switch(config)#

interface fastEthernet 2

switch(config-if)#

stp-admin-edge True

stp-admin-non-stp

[True|False]

I

Admin NonSTP of STP priority on
this interface.

switch(config)#

interface fastEthernet 2

switch(config-if)#

stp-admin-non-stp False

show spanning-tree

E

Displays a summary of the
spanning-tree states.

switch>

show spanning-tree

no spanning-tree

G

Disable spanning-tree.

switch(config)#

no spanning-tree

3.2.8

QOS Commands Set

Table 3.8: QOS Commands Set

Commands

Level

Description

Example

qos policy

[weighted-fair|strict]

G

Select QOS policy scheduling

switch(config)#

qos policy weighted-fair

qos prioritytype

[port-based|cos-only|tos-only|cos-
first|tos-first]

G

Setting of QOS priority type

switch(config)#

qos prioritytype

qos priority portbased

[Port] [lowest|low|middle|high]

G

Configure Port-based Priority

switch(config)#

qos priority portbased 1 low

qos priority cos

[Priority][lowest|low|middle|high]

G

Configure COS Priority

switch(config)#

qos priority cos 0 middle

qos priority tos

[Priority][lowest|low|middle|high]

G

Configure TOS Priority

switch(config)#

qos priority tos 3 high

39

Chapter3

«
...
37
38
39
40
41
...
»

Содержание EKI-7556MI










































































































Отзывы:

Нет отзывов