Advantech EKI-7556MI Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 105

Advantech EKI-7556MI Скачать руководство пользователя страница 92

3.3.4 Security

In this section, you can configure 802.1x and MAC address table.

802.1X/Radius Configuration

802.1x is an IEEE authentication specification which prevents the client from connecting to a wireless
access point or wired switch until it provides authority, like the user name and password that are verified
by an authentication server (such as RADIUS server).

802.1X/Radius - System Configuration

After enabling the IEEE 802.1X function, you can configure the parameters of this function.

•

IEEE 802.1x Protocol:

Enable or disable 802.1x protocol.

•

Radius Server IP:

Assign the RADIUS Server IP address.

•

Server Port:

Set the UDP destination port for authentication requests to the specified RADIUS Server.

•

Accounting Port:

Set the UDP destination port for accounting requests to the specified RADIUS

Server.

•

Shared Key:

Set an encryption key for using during authentication sessions with the specified

RADIUS server. This key must match the encryption key used on the RADIUS Server.

•

NAS, Identifier:

Set the identifier for the RADIUS client.

•

Click

Apply

.

Figure 3.3-43

802.1x/Radius System Configuration

EKI-7556MI_Manual

92

«
...
90
91
92
93
94
...
»

Содержание EKI-7556MI










































































































Отзывы:

Нет отзывов