Advantech EKI-7556MI Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 105

Advantech EKI-7556MI Скачать руководство пользователя страница 25

2.4 Network

Connection

The EKI-7556MI has 16 x RJ-45 ports that support connection to 10 Mbps Ethernet, or 100 Mbps Fast
Ethernet, and half or full duplex operation. EKI-7556MI can be connected to other hubs or switches via a
twisted-pair straight-through or crossover cable up to 100m long. The connection can be made from any
TX port of the EKI-7556MI (MDI-X) to another hub or switch either MDI-X or uplink MDI port.

The EKI-7556MI supports auto-crossover to make networking more easy and flexible. You can connect
any RJ-45 (MDI-X) station port on the switch to any device such as a switch, bridge or router.

2.5 Power

Connection

The EKI-7556MI supports dual +12 ~ 48 V

DC

power inputs and power-fail relay output.

Figure 2.5-1

Pinouts of the Power Connector

You can connect an alarm indicator, buzzer or other signaling equipment through the relay output. The
relay opens if power input 1, 2 fails or port link down/break (‘Open’ means if you connect relay output
with an LED, the light would be off).

25 Chapter2

«
...
23
24
25
26
27
...
»

Содержание EKI-7556MI










































































































Отзывы:

Нет отзывов