Advantech EKI-7556MI Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 105

Advantech EKI-7556MI Скачать руководство пользователя страница 72

Port Mirroring

The Port mirroring is a method for monitoring traffic in switched networks. Traffic through ports can be
monitored by one specific port which means traffic goes in or out monitored (source) ports will be
duplicated into mirroring (destination) port.

•

Destination Port:

There is only one port can be selected to be the destination (mirroring) port for

monitoring both RX and TX traffic which come from the source port. Or, use one of two ports for
monitoring RX traffic only and the other one for TX traffic only. The user can connect the mirroring port
to LAN analyzer or Netxray.

•

Source Port:

The ports that the user wants to monitor. All monitored port traffic will be copied to

mirroring (destination) port. The user can select multiple source ports by ticking the

RX

or

TX

checkboxes to be monitored.

•

And then, click

Apply

.

Figure 3.3-26

Port Mirroring

EKI-7556MI_Manual

72

«
...
70
71
72
73
74
...
»

Содержание EKI-7556MI










































































































Отзывы:

Нет отзывов