Advantage-Devices Wi232 Скачать руководство пользователя

Страница: 7 / 75

Wi232/WiUSB User Guide

Contents

3.7

Configurable Pins ............................................................................................... 3-14

3.8

Apply Settings .................................................................................................... 3-14

3.9

Apply Factory Defaults ....................................................................................... 3-15

Configuration via Serial Mode or Telnet Port ................................................................. 4-1

4.1

Server Configuration ............................................................................................ 4-2

4.2

Channel 1 Configuration ...................................................................................... 4-3

4.2.1

Baudrate ............................................................................................... 4-3

4.2.2

I/F (Interface) Mode ............................................................................. 4-4

4.2.3

Flow ..................................................................................................... 4-4

4.2.4

Port Number ......................................................................................... 4-5

4.2.5

Connect Mode ...................................................................................... 4-6

4.2.6

Send the Escape Sequence (+++) in Modem Mode .................................................... 4-11

4.2.7

Auto Increment Source Port ................................................................ 4-11

4.2.8

Remote IP Address ............................................................................. 4-11

4.2.9

Remote Port........................................................................................ 4-12

4.2.10

DisConnMode .................................................................................. 4-12

4.2.11

Flush Mode ...................................................................................... 4-13

4.2.12

DisConnTime (Inactivity Timeout) ................................................... 4-14

4.2.13

SendChar 1 and SendChar2 ............................................................... 4-15

4.2.14

Telnet Terminal Type ....................................................................... 4-15

4.2.15

Channel (Port) Password .................................................................. 4-15

4.3 E-mail ................................................................................................................. 4-15
4.4

WLAN Settings .................................................................................................. 4-15

4.5

Expert Settings ................................................................................................... 4-17

4.6

Security Settings ................................................................................................ 4-18

4.6.1

Disable SNMP ................................................................................... 4-18

4.6.2

SNMP Community Name ................................................................... 4-18

4.6.3

Disable Telnet Setup........................................................................... 4-18

4.6.4

Disable TFTP Firmware Upgrade ....................................................... 4-19

4.6.5

Disable Port 77FE (Hex) ..................................................................... 4-19

4.6.6

Disable Web Server ............................................................................ 4-19

4.6.7

Disable Web Setup ............................................................................. 4-19

4.6.8

Disable ECHO Ports ........................................................................... 4-19

4.6.9

Enable Encryption .............................................................................. 4-19

4.6.10

Enable Enhanced Password .............................................................. 4-19

4.6.11

Disable Port 77F0h ........................................................................... 4-19

4.7

Factory Defaults ................................................................................................. 4-20

4.7.1

Exit Configuration Mode .................................................................... 4-21

Monitor Mode ................................................................................................................... 5-1

5.1.1

Entering Monitor Mode via the Serial Port .............................................. 5-1

5.1.2

Entering Monitor Mode via the Network Port .............................................. 5-1

5.1.3

Monitor Mode Commands .................................................................... 5-1

Updating Firmware ......................................................................................................... 6-1

6.1

Obtaining Firmware ............................................................................................. 6-1

6.1.1

Reloading Firmware ............................................................................. 6-1

6.1.2

Via Device Installer .............................................................................. 6-1

Troubleshooting ............................................................................................................... 7-1

7.1.1 Problems and Error Messages ............................................................... 7-1

Содержание Wi232












































































Результаты поиска

Содержание Wi232

Отзывы:

Похожие инструкции для Wi232

Бренды по названию

Популярные бренды

Advantage-Devices Wi232, Руководство пользователя

Результаты поиска

Содержание Wi232

Отзывы:

Похожие инструкции для Wi232

Бренды по названию

Популярные бренды