Advantage-Devices Wi232 Скачать руководство пользователя | Manualshive

Страница: 59 / 75

background image

Wi232/WiUSB User Guide

4-13

4.2.11 Flush Mode

The FlushMode (buffer flushing) parameter controls line handling and network buffers with connection startup
and disconnect.

FlushMode ( 0) ? _

Select between two different packing algorithms (the current configuration is displayed within the
parentheses). Available Flush Mode options are:

Flush Mode Options

Function

7

6

5

4

3

2

1

0

Input Buffer (Serial to Network)

Clear with a connection that is initiated from
the device to the network

1

Clear with a connection initiated from the
network to the device

1

Clear when the network connection to or from
the device is disconnected

1

Output Buffer (Network to Serial)

Clear with a connection that is initiated from
the device to the network

1

Clear with a connection initiated from the
network to the device

1

Clear when the network connection to or from
the device is disconnected

1

Alternate Packing Algorithm (Pack Control)

Enable

1

«
...
57
58
59
60
61
...
»

Содержание Wi232












































































Отзывы:

Нет отзывов

Похожие инструкции для Wi232

Бренд: H3C Страницы: 37

Бренд: Rocstor Страницы: 2

Бренд: National Instruments Страницы: 2

Бренд: LevelOne Страницы: 29

Бренд: HIKOKI Страницы: 100

Бренд: StarTech.com Страницы: 2

Бренд: VOLTCRAFT Страницы: 4

Бренд: StarTech.com Страницы: 10

Бренд: Skross Страницы: 2

Бренд: 3idee Страницы: 7

Бренд: Velleman Страницы: 18

Бренд: Prudent Way Страницы: 6

Бренд: Siemens Страницы: 4

Бренд: Askey Страницы: 5

Бренд: Alpine Страницы: 102

Бренд: SeaLevel Страницы: 11

Бренд: Siemens Страницы: 4

Бренд: Siemens Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды