ADTRAN Express XL Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 187

background image

Chapter 3: Terminal Menu Operation and Structure

61200070L1-1

Express XL/XLT User Manual

67

Authentication/Call ID 1

Write security: 1; Read security: 3
The caller identification from the ISDN incoming call is compared to this num-
ber, starting from the right digits.

Authentication/Call ID 2

Write security: 1; Read security: 3
The caller identification from the ISDN incoming call is compared to this num-
ber, starting from the right digits.

Connection List/IP

The IP menu contains the parameters for exchanging IP data with the PPP
peer. Static routes can also be created from here for IP dial-on-demand appli-
cations.

IP/Mode

Write security: 3; Read security: 5
Setting to

On

(def) will permit this connection profile to negotiate PPP IPCP

with the PPP peer for exchanging of IP packets.

IP/NAT

Write security: 3; Read security: 5
The Express XL/XLT can perform Network Address Translation. This feature
is most widely used when connecting to the Internet. The Ethernet network
can consist of private network numbers. When this profile is connected, all IP
addresses on the Ethernet side are translated into the one real IP address ne-
gotiated with the PPP peer (ISP). Multiple stations on the Ethernet side can ac-
cess the Internet simultaneously. See the section IP/NAT on page 43 for more
global options. Setting this option to

On

will cause the Express XL/XLT to

perform NAT. In the

Off

(def) position, the unit will route across the connec-

tion normally.

IP/Route

The IP parameters are configured in this menu. Adjusting these parameters is
only necessary for certain dial-on-demand applications. Usually the Express XL/XLT
will automatically discover the PPP peer’s networks using PPP IPCP and/or RIP.

«
...
81
82
83
84
85
...
»

Содержание Express XL




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Express XL

grandMA2 Series

Бренд: MA lighting Страницы: 36

Бренд: Paradyne Страницы: 11

Бренд: Paradyne Страницы: 19

Бренд: Paradyne Страницы: 32

COMSPHERE 3550 Series

Бренд: Paradyne Страницы: 153

Jetstream CPX-1000

Бренд: Paradyne Страницы: 141

FrameSaver 9783

Бренд: Paradyne Страницы: 28

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 7

Бренд: Black Box Страницы: 9

Бренд: Lanner Страницы: 78

Бренд: Juniper Страницы: 190

Бренд: US Robotics Страницы: 36

Бренд: Allnet Страницы: 12

Бренд: Telebyte Страницы: 19

Бренд: Telex Communications Страницы: 28

Fan Tray 8820-S2-900

Бренд: Paradyne Страницы: 6

SABVISION NVR32

Бренд: SAB Страницы: 29

Elinx ESW200 Series

Бренд: B&B Electronics Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды