ADTRAN Express XL Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 187

background image

Chapter 3: Terminal Menu Operation and Structure

86

Express XL/XLT User Manual

61200070L1-1

Traps/Manager Name

Write security: 2; Read security: 4
This is the text string describing the name of the entry. It is intended for easy
reference and has no bearing on the SNMP trap function.

Traps/Manager IP

Write security: 2; Read security: 4
This is the IP address of the manager that is to receive the traps.

Management/Maint Port

The Express XL/XLT has an EIA-232 connector on the back of the unit. The
setup for that port is under this menu.

Maint Port/Password Protect

Write security: 0; Read security: 1
When set to

No

, the maintenance port is not password protected. When

On

(def), the Express XL/XLT will prompt for a password upon startup.

Maint Port/Password

Write security: 0; Read security: 1
This is the text string that is used for comparison when password protecting
the maintenance port. By default, no password is entered.

The security level for the maintenance port is always set to 0. This gives full access to

all menus.

Maint Port/Baud Rate

Write security: 5; Read security: 5
This is the asynchronous rate that the maintenance port will run. The possible
values are 300, 1200, 2400, 4800, 9600 (def)

,

19200, 38400, 57600, 115200.

Maint Port/Data Bits

Write security: 5; Read security: 5
This is the asynchronous bit rate that the maintenance port will run. The pos-
sible values are 7

or 8 (def)

bits.

«
...
100
101
102
103
104
...
»

Содержание Express XL




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Express XL

Бренд: D-Link Страницы: 12

Бренд: DBM Страницы: 50

Бренд: LAWO Страницы: 154

4-Port 10/100Mbps Ethernet Broadband Router

Бренд: AOpen Страницы: 41

Бренд: XNET Страницы: 17

Бренд: Juniper Страницы: 825

JetNet 3508-LVDC

Бренд: Korenix Страницы: 16

Бренд: PaloAlto Networks Страницы: 28

8-Port 10/100Mbps Fast Ethernet Switch

Бренд: Amer.com Страницы: 14

Wisenet PRN-6400DB4

Бренд: Hanwha Techwin Страницы: 125

Бренд: DPS Telecom Страницы: 80

Бренд: Sharedband Страницы: 3

CNGE28FX4TX24MS2

Бренд: Comnet Страницы: 154

Бренд: HighPoint Страницы: 3

DSL906 1DA Series

Бренд: Aztech Страницы: 15

Бренд: Johnson Controls Страницы: 10

DGS-1510 Series

Бренд: D-Link Страницы: 711

Бренд: Crestron Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды