ADTRAN Express XL Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 187

background image

Chapter 3: Terminal Menu Operation and Structure

61200070L1-1

Express XL/XLT User Manual

81

Filters/Out Exceptions

Write security: 2; Read security: 5
This is a list of up to 32 filter entries. The setup is exactly the same as the

Filter/

In Exceptions

list.

Filters/Demand Dial

Write security: 2; Read security: 5
The demand dial filters have two purposes: 1) cause the Express XL/XLT in
Bridge mode to dial this Connection List profile, and 2) determine which traf-
fic will cause the idle timer to be reset, keeping the connection active. The lat-
ter is used in Bridge or IP/IPX Router mode. The idle timer is a timer in the
Express XL/XLT which continually increments until it reaches the idle time-
out parameters value set in the Connection List, at which point the connection
is hung-up.

When this filter is enabled, direct control can be placed over which packets are
considered as demand and which are ignored. Packets that are ignored cause
a connection not to be dialed and do not reset the idle timer of an active con-
nection. This is especially helpful for bridged connections since bridges can-
not easily distinguish true demand traffic from overhead traffic like certain
broadcast and multicast packets. There are three possible selections for this
parameter:

Disabled

(def) - Turns off demand dial filtering. No packets cause

demand dialing for this profile and all outgoing and incoming

packets reset the idle timer.

Ignore All

- When connected in any mode (Bridge, IP Router, or

IPX router), the idle timer is reset only when there is a match in

the

Filters/Dem Dial Exceptions

list. When not connected in

Bridge mode only, causes the Express XL/XLT to dial using this

Connection List profile if there is a match in the

Filters/Dem Dial

Exceptions

.

Demand All

- When connected in any mode (Bridge, IP Router, or

IPX router), the idle timer is always reset except when there is a

match in the

Filters/Dem Dial Exceptions

list. When not

connected in Bridge mode only, causes the Express XL/XLT to

dial using this Connection List profile if there is NOT a match in

the

Filters/Dem Dial Exceptions

list.

«
...
95
96
97
98
99
...
»

Содержание Express XL




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Express XL

Бренд: Patton electronics Страницы: 2

Бренд: Mafell Страницы: 162

OXTOPUS EIA-709

Бренд: OCCITALINA Страницы: 54

Бренд: Lindy Страницы: 4

Бренд: Direct IP Страницы: 76

MultiConnect SE MTS2EA

Бренд: Multitech Страницы: 2

Бренд: E-LINX Страницы: 24

Бренд: Z-Wave Страницы: 6

Бренд: Teletronics International Страницы: 57

Бренд: INNOSILICON Страницы: 11

Бренд: Airlinkplus Страницы: 20

Бренд: Allied Telesis Страницы: 80

Бренд: Conel Страницы: 32

Air Live GW-300R

Бренд: Ovislink Страницы: 20

EZ Switch SMC-EZ1024FDT

Бренд: SMC Networks Страницы: 4

Бренд: Planet Страницы: 66

Бренд: METREL Страницы: 21

Бренд: PairGain Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды