ADTRAN Express XL Скачать руководство пользователя страница 169

Страница: 169 / 187

Glosssary

61200070L1-1

Express XL/XLT User Manual

153

message

The Layer 3 information that is passed between the CPE and SPCS for signal-

ling.

multipoint line

A communications line having multiple cable access points.

Name Binding Protocol (NBP)

The AppleTalk transport-level protocol that translates a character string name

into the internet address of the corresponding socket client; NBP enables Ap-

pleTalk protocols to understand user-defined zones and device names by pro-

viding and maintaining translation tables that map these names to

corresponding socket addresses.

NAT

Network Address Translation occurs at the borders of stub domains. Its pur-

pose is to translate the IP address of passing packets by changing all references

of one IP address to another. Translation is performed as per RFC 1631.

netmask

A 32-bit bit mask which shows how an Internet address is to be divided into

network, subnet, and host parts. The netmask has ones in the bit positions in

the 32-bit address which are to be used for the network and subnet parts, and

zeros for the host part. The mask should contain at least the standard network

portion (as determined by the address's class), and the subnet field should be

contiguous with the network portion.

non-ISDN line

Any connection from a CPE to a SPCS that is not served by D-Channel signal-

ling.

non-ISDN trunk

Any trunk not served by either SS7 or D-Channel signalling.

NT1

Network Termination 1. A unit that provides physical and electromagnetic

termination of the U-interface 2-wire transmission line, converts between Lay-

er 1 formats used at the U- and T- reference points, and performs some main-

tenance functions.

phase jitter

In telephony, the measurement in degrees out-of-phase that an analog signal

deviates from the reference phase of the main data-carrying signal. Often

caused by alternating current components in a telecommunications network.

Содержание Express XL




























































































































































































Результаты поиска

Содержание Express XL

Отзывы:

Похожие инструкции для Express XL

Бренды по названию

Популярные бренды

ADTRAN Express XL, Руководство пользователя

Результаты поиска

Содержание Express XL

Отзывы:

Похожие инструкции для Express XL

Бренды по названию

Популярные бренды