ADTRAN Express XL Скачать руководство пользователя страница 134

Страница: 134 / 187

Appendix A: Loop Status Messages

118

Express XL/XLT User Manual

61200070L1-1

DISCONNECTING

A call is in the process of being disconnected.

DMS-100 Ready

The ISDN link layers 1 through 3 are up against a Nortel DMS-100 switch and
is ready for calls.

Echo: Tx: X Rx: Y

The current transmit and receive count for the PPP echo request test.

Getting TEI #1

The Express XL/XLT’s ISDN layer 1 is up and is now getting the first TEI from
the ISDN network.

Getting TEI #2

The Express XL/XLT’s ISDN layer 1 is up and one TEI is obtained. It is now
getting the second TEI from the ISDN network.

ISDN-1 Ready

The ISDN link layers 1 through 3 are up against a switch running the ISDN-1
protocol and is ready for calls.

Layer 1 up

The Express XL/XLT’s ISDN layer 1 is up.

Link down

The ISDN link is not synchronized.

Link In Sync

The ISDN link is synchronized but layer 1 is not up.

NET EOC LOOPBACK

Express XL/XLT has received an ISDN EOC loopback command from the
switch.

Register SPID #1

The Express XL/XLT’s ISDN layer 1 and 2 is up and is now registering SPID 1
with the ISDN network.

Содержание Express XL




























































































































































































Результаты поиска

Содержание Express XL

Отзывы:

Похожие инструкции для Express XL

Бренды по названию

Популярные бренды

ADTRAN Express XL, Руководство пользователя

Результаты поиска

Содержание Express XL

Отзывы:

Похожие инструкции для Express XL

Бренды по названию

Популярные бренды