ADTRAN Express XL Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 187

background image

Chapter 3: Terminal Menu Operation and Structure

61200070L1-1

Express XL/XLT User Manual

45

IP/UDP Relay

The Express XL/XLT can be configured as a relay agent for UDP broadcast
packets. Normally, a router will not forward UDP broadcast packets. How-
ever, many network application use UDP broadcasts to configure addresses,
host names, and other information. If hosts using these protocols are not on the
same network segment as the servers providing the information, the client
programs will not receive a response without enabling the UDP relay agent.

UDP Relay/Mode

Write security: 3; Read security: 5
When this option is set to

On

(def),

the Express XL/XLT will act as a relay

agent.

UDP Relay/UDP Relay List

Up to four relay destination servers can be specified in this list.

UDP Relay List/Relay Address

Write security: 3; Read security: 5
This is the IP address of the server that will receive the relay packet.

UDP Relay List/UDP Port Type

Write security: 3; Read security: 5

Standard

(def)

- The following standard UDP protocols are

relayed when set: DHCP, TFTP, DNS, NTP (Network

Time Protocol, port 123). NBNS (NetBIOS Name Server, port 137),

NBDG (NetBIOS Datagram, port 138), and BootP.

Specified

- When set, the UDP port (1 to 65535) can be specified in

the UDP Port columns. (up to a maximum of three per server)

UDP Relay List/UDP Port 1, UDP Port 2, UDP Port 3

Write security: 3; Read security: 5
UDP Port 1, UDP Port 2, and UDP Port 3 are used for specifying UDP ports to
be relayed. These fields only apply when

UDP Port Type

is set to

Specified

.

«
...
59
60
61
62
63
...
»

Содержание Express XL




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Express XL

Бренд: H3C Страницы: 1057

IntelliJack NJ200

Бренд: 3Com Страницы: 4

Бренд: B+B SmartWorx Страницы: 4

Бренд: National Instruments Страницы: 26

Бренд: National Instruments Страницы: 85

Module SCXI-1503

Бренд: National Instruments Страницы: 79

Бренд: Speedtouch Страницы: 124

Net2Air Ins-40085-US

Бренд: Paxton Страницы: 4

Бренд: ZyXEL Communications Страницы: 215

BROADCAST POLLING FRAD BPF-14 BU

Бренд: DCB Страницы: 28

Бренд: Planet Страницы: 2

Бренд: ADTRAN Страницы: 20

Бренд: Maestro Wireless Solution Страницы: 22

Бренд: LevelOne Страницы: 83

Бренд: Black Box Страницы: 12

Routers and Switches

Бренд: Allied Telesis Страницы: 15

LS-5100-16P-SI-OVS-H3

Бренд: H3C Страницы: 313

SA-REP-ETHERLINK_II-1DA-PL

Бренд: S-Access Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды