ADMtek ADM5120 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 112

ADMtek ADM5120 Скачать руководство пользователя страница 94

ADM5120

Register Description

Bit # Type Name

Descriptions

Initial Value

HIGH
(reset value on nPOR).For writes the respective active
bits in
nMPMCBLSOUT[3:0] are LOW.
1 = For reads the respective active bits in
nMPMCBLSOUT[3:0] are LOW. For writes the
respective
active bits in nMPMCBLSOUT[3:0] are LOW.

8 R/W

EW

Extended

wait:

0 = extended wait disabled (reset value on nPOR)
1=extended wait enabled.

0

18:9

Reserved

Read undefined, must be written as zeros.

19 R/W

B

Buffer

enable:

0 = write buffer disabled (reset value on nPOR)
1=write buffer enabled.

0

20 R/W

P

Write

protect:

0 = writes not protected (reset value on nPOR)
1 = write protected.

0

31:21

Reserved

Read undefined, must be written as zeros.

Note:

Synchronous burst mode memory devices are not supported.

4.7.22 MPMC Static Wait Wen [0,1,2,3] register

Note:

offset = 200h, 220h, 240h is for SMC_CSZ0, SMC_CSZ1, and SMC_CSZ2

respectively

Bit #

Name

Descriptions

3:0

R/W WAITWEN

Wait write enable: delay from chip select assertion to
write enable.
0000 = one HCLK cycle delay between assertion of
chip select and write enable (reset value on nPOR)
0001 to 1111 = (n+1) HCLK cycle delay.

0000

31:4

Reserved

Read undefined, must be written as zeros.

Type

Initial Value

Note:

The delay is (1) x tHCLK.

4.7.23 MPMC Static Wait Oen[0,1,2,3] register

Note:

offset = 200h, 220h, 240h is for SMC_CSZ0, SMC_CSZ1, and SMC_CSZ2

respectively

ADMtek Inc.

4-47

Bit # Type Name

Descriptions

Initial Value

3:0

R/W WAITOEN

Wait output enable: delay from chip select assertion to
output enable.
0000 = No delay (reset value on nPOR)
0001 to 1111 = n cycle delay.

0000

31:4

Reserved

Read undefined, must be written as zeros.

«
...
92
93
94
95
96
...
»

Содержание ADM5120

















































































































Отзывы:

Нет отзывов