ADMtek ADM5120 Скачать руководство пользователя

Страница: 74 / 112

ADM5120

4.6 USB Control Status Registers Description

Host processors can only access USB 1.1 host/device controller registers with double
word (32 bits) reads or writes on double word boundaries.

4.6.1 General Control , offset 0x00

Bits

Type Name

Description

Initial value

0 R/W

HOST_EN

USB Host function enable, Both modes:

This bit enables the USB host functions, when 1’b1, the
controller acts as USB host

1 R/W

SW_INT_REQ

Software interrupt request, Both modes:

When this bit is set to 1, the controller’s interrupt pin
become active. Reading this bit always returns zero.
When SW_INT in interrupt is clear, this bit is clear as
well.

2 R/W

DMA_ARB

DMA Arbitration control, Both modes:

0 : Receive = Transmit (1:1)
1 : Receive > Transmit

3 R/W

SW_RESET

Software reset, Both modes:

Setting this bit resets the device controller to its initial
state. This bit is auto-cleared after reset. Writing a 0 to
this bit takes no effect.

31:4 RO

Reserved

Not

Applicable

4.6.2 Interrupt Status, offset 0x04

ADMtek Inc.

4-27

Bits

Type Name

Description

Initial value

3:0 R/W1

Reserved Not

Applicable

4 R/W1

SOF_INT

SOF Transmitted/Received, Host mode:

1: Issue a SOF token. The frame number value is stored
in 0x1C Frame Number.

5 R/W1

RES_INT

Resume detected

1: USB resume event is detected. Controller set this bit
to one when resume signal is detected on USB bus.

6 R/W1

Reserved Not

Applicable

7 R/W1

Reserved Not

Applicable

8 R/W1

BAB_INT

Babble detected, Host mode:

1: Detected babble.

9 R/W1 INSMOV_INT

Root Hub status change:

Содержание ADM5120

















































































































Результаты поиска

Содержание ADM5120

Отзывы:

Похожие инструкции для ADM5120

Бренды по названию

Популярные бренды

ADMtek ADM5120, Техническое описание

Результаты поиска

Содержание ADM5120

Отзывы:

Похожие инструкции для ADM5120

Бренды по названию

Популярные бренды