ADLINK Technology LittleBoard 735 Скачать руководство пользователя

Страница: 7 / 54

LittleBoard 735

Reference Manual

Chapter 1

About This Manual

Purpose of this Manual

This manual is for designers of systems based on the LittleBoard™ 735 single board computer (SBC). This

manual contains information that permits designers to create an embedded system based on specific design
requirements.

Information provided

in this reference manual includes:

•

LittleBoard 735 specifications

•

Environmental requirements

•

Major integrated circuits (chips) and features implemented

•

LittleBoard 735 connector/pin numbers and definitions

•

BIOS Setup information

Information not provided

in this reference manual includes:

•

Detailed chip specifications

•

Internal component operation

•

Standard connector pin-out tables

•

Internal registers or signal operations

•

Bus or signal timing for industry standard busses and signals

References

The following list of references may be helpful for you to complete your design successfully. Most of these
references are also available on the Ampro By ADLINK web site in the InfoCenter. The InfoCenter was

created for embedded system developers to share ADLINK’s knowledge, insight, and expertise.

Specifications

•

EBX Spec Revision 2.0, March 1, 2005

For the latest version of the EBX specifications, contact the PC/104 Consortium, at:

Web site:

http://www.pc104.org

•

PCI Express Mini Card Spec Revision 1.0

For latest revision of the PCI Express Mini Card specifications, contact the PCI Special Interest
Group Office, at:

Web site:

http://www.pcisig.com/specifications/pciexpress/mini

•

PC/104 Spec Revision 2.5, November 2003

•

PC/104-Plus Spec Revision 2, November 2003

For latest revision of the PC/104 specifications, contact the PC/104 Consortium, at:

Web site:

http://www.pc104.org

•

PCI 2.2 Compliant Specifications

For latest revision of the PCI specifications, contact the PCI Special Interest Group Office at:

Web site:

http://www.pcisig.com

Содержание LittleBoard 735























































Результаты поиска

Содержание LittleBoard 735

Отзывы:

Похожие инструкции для LittleBoard 735

Бренды по названию

Популярные бренды

ADLINK Technology LittleBoard 735, Справочное руководство

Результаты поиска

Содержание LittleBoard 735

Отзывы:

Похожие инструкции для LittleBoard 735

Бренды по названию

Популярные бренды