ADLINK Technology LittleBoard 735 Скачать руководство пользователя | Manualshive

Страница: 41 / 54

background image

Chapter 3

Hardware

LittleBoard 735

Reference Manual

35

Note:

The shaded areas denote power or ground. The +12V and +3.3V on the Power Supply Input
header (J19) are used for the PCI, ISA bus, and LVDS power, which are supplied externally and
not generated on the LittleBoard 735. The -5V and -12V used for the PC/104 bus are supplied
through the PC/104 bus or from an external power supply through the Utility 1 header (J15).

ATX Power Interface

Table 3-18

lists the pin signals for the J30 Power-On header, which uses 3 pins, single row with 0.100"

(2.54mm) pitch.

Note:

The shaded areas denote power or ground. The signals marked with * = Negative true logic.

Power-On Button Interface

A Power-On Button signal is provided by connecting ground to pin-1 on this header (J46). A Reset Switch
signal is provided by connecting ground to pin 3 on this header.

Table 3-19

lists the pin signals for the J46 Power On Button header, which uses 5 pins, single row with

0.100" (2.54mm) pitch.

Note:

The shaded area denotes power or ground.

Table 3-18. ATX Power Header Pin Signals (J30)

Pin #

Signal

Description

1

PS_ON*

Power Supply On – This signal is sent to the ATX power supply by the
LittleBoard 735 to turn On the ATX power supply. This signal can also
be used to turn Off the ATX power supply or go into a suspended or
standby state.

2

GND

Ground

3

VCC5_AT5V suspend voltage (+5V, 500mA Standby) – This voltage is

supplied from ATX power supply. This voltage is required for normal
operation.

NOTE

If the +5V suspend voltage is not present on the Power On connector (J30, pin
1) the LittleBoard 735 will not completely power on. The board will have
power (+5V), but it will not start the boot process and will never completely
power up.

Table 3-19. Power-On Button Interface Pin Signals (J46)

Pin #

Signal

Description

1

PWRON

Power-On Button input (connect between pins 1 & 2)

2

GND

Ground

3

RST_SW

Reset Switch input or output (connect between pins 3 & 2)

4

NC

Not Connected

5

NC

Not Connected

«
...
39
40
41
42
43
...
»

Содержание LittleBoard 735























































Отзывы:

Нет отзывов

Похожие инструкции для LittleBoard 735

Бренд: hager Страницы: 4

Бренд: Uctronics Страницы: 27

Бренд: IEI Technology Страницы: 126

Бренд: P&E Microcomputer Systems Страницы: 53

Бренд: ST Страницы: 15

Бренд: QDI Страницы: 20

Fatal1ty Z87 Killer Series

Бренд: ASROCK Страницы: 102

Бренд: JETWAY Страницы: 44

Бренд: Gigabyte Страницы: 116

Бренд: QDI Страницы: 47

Бренд: Supero Страницы: 85

Бренд: MSI Страницы: 126

Side-Power SX100/185T

Бренд: SLEIPNER MOTOR AS Страницы: 16

Бренд: Octek Страницы: 84

Бренд: Rohm Страницы: 8

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды