ADLINK Technology LittleBoard 735 Скачать руководство пользователя

Страница: 21 / 54

Chapter 2

Product Overview

LittleBoard 735

Reference Manual

Environmental Specifications

Table 2-5

provides the most efficient operating and storage condition ranges required for this board.

Power Specifications

Table 2-6

shows the power requirements from the baseboard and the board power output.

Operating configurations:

•

In-rush operating configuration includes video, 2GB DDR2 RAM, and power.

•

Idle operating configuration includes the in-rush configuration as well as one IDE hard drive, I/O board,
keyboard, and mouse.

•

BIT = Burn-In-Test. Operating configuration includes idle configuration as well as two SATA hard
drives, one on-board Compact Flash, one floppy drive, four serial loop-backs, one parallel loop-back,

two Ethernet connections, four USB loop-backs, one USB flash drive, and one Compact Flash reader
with 64MB Compact Flash.

Thermal/Cooling Requirements

The CPU, Memory Hub, I/O Hub, and voltage regulators are the sources of heat on the board. The

LittleBoard 735 is designed to operate at the maximum speed of the CPU: 1.6GHz. The Atom N270 CPU

requires a heatsink but no fan for -40°C to +85°C operation.

Table 2-5. Environmental Requirements

Parameter

1.6GHz Atom N270
Conditions

emperatur

Operating

-20° to +70°C
(-4° to +158°F)

Extended
(Optional)

–40° to +85°C
(–40° to +185°F)

Storage

–55° to +85°C
(–67° to +185°F)

midity

Operating

5% to 95%
relative humidity,
non-condensing

Non-operating

5% to 95%
relative humidity,
non-condensing

Table 2-6. Power Supply Requirements

Parameter

1.6GHz Atom N270
Characteristics

Input Type

Regulated DC voltages

In-rush Current

6.59A (32.95W)

Idle Power

1.09A (5.46W)

BIT Current

2.36A (11.78W)

Содержание LittleBoard 735























































Результаты поиска

Содержание LittleBoard 735

Отзывы:

Похожие инструкции для LittleBoard 735

Бренды по названию

Популярные бренды

ADLINK Technology LittleBoard 735, Справочное руководство

Результаты поиска

Содержание LittleBoard 735

Отзывы:

Похожие инструкции для LittleBoard 735

Бренды по названию

Популярные бренды