ADLINK Technology LittleBoard 735 Скачать руководство пользователя

Страница: 37 / 54

Chapter 3

Hardware

LittleBoard 735

Reference Manual

Audio Interface

The audio solution on the LittleBoard 735 is provided by the Realtek ALC203-LF audio CODEC. The chip

is defined by AC97 and is revision 2.2 compliant. The audio interface signals are supplied to the 26-pin
2mm connector (J9). Refer to the following list for the

Audio CODEC

(ALC203-LF) features.

•

Analog Mixer Dynamic Range 97dB (typ)

•

D/A Dynamic Range 89dB (typ) and A/D Dynamic Range 90dB (typ)

•

AC’97 Rev 2.1 compliant

•

High quality Sample Rate Conversion (SRC) from 4kHz to 48kHz

•

3D Sound circuitry and PC-Beep passthrough to Line Out while reset is held active low

•

True Line Level Output with volume control independent of Line Out

Table 3-13

describes the pin signals of the audio interface which uses 26 pins, 2 rows, odd/even sequence (1,

2) with 0.079" (2mm) pitch.

Note:

The shaded areas denote power or ground.

Table 3-13. Audio Interface Pin Signals (J9)

Pin #

Signal

Description

Not connected (Video Audio In signal left channel)

VIDEO_GND

Video Audio ground

Not connected (Video Audio In signal right channel)

CD_L

CD-ROM signal left channel

CD_GND

CD-ROM Audio ground

CD_R

CD-ROM signal right channel

LINE_IN_L

Line In signal left channel

LINE_IN_GND

Line In Audio ground

LINE_IN_R

Line In signal right channel

MIC1

Microphone In signal 1 or left channel

MIC_GND

Microphone Audio ground

MIC2

Microphone In signal 2 or right channel

MIC_REF

Microphone reference signal

NC/KEY

Not Connected - Key

PHONE_IN

Phone signal In

PHONE_GND

Phone Audio ground

MONO_OUT

Monaural signal Out

MONO_GND

Monaural Audio ground

+AOUT_L

+ Audio Out signal Left channel

-AOUT_L

- Audio Out Left ground

+AOUT_R

+ Audio Out signal Right channel

-AOUT_R

- Audio Out Right ground

GND

Audio Ground (tied to all audio grounds)

HP_L

Headphone signal Left channel

HP_R

Headphone signal Right channel

Not Connected (Headphone In)

Содержание LittleBoard 735























































Результаты поиска

Содержание LittleBoard 735

Отзывы:

Похожие инструкции для LittleBoard 735

Бренды по названию

Популярные бренды

ADLINK Technology LittleBoard 735, Справочное руководство

Результаты поиска

Содержание LittleBoard 735

Отзывы:

Похожие инструкции для LittleBoard 735

Бренды по названию

Популярные бренды