ADLINK Technology LittleBoard 735 Скачать руководство пользователя

Страница: 11 / 54

Chapter 2

Product Overview

LittleBoard 735

Reference Manual

Board Features

•

CPU features

♦

Intel 1.6GHz LV, Atom N270 Processor

♦

512KB L2 cache

♦

533MHz FSB

•

Memory

♦

Single standard 200-pin DDR2 SODIMM socket

♦

Supports non-ECC, unbuffered memory

♦

Su2.5V DDR2, 533MHz RAM up to 2GB

•

PC/104-Plus Bus Interfaces

♦

PCI Bus up to 33MHz

♦

PCI 2.2 compliant signals

♦

PC/104 (ISA) Bus up to 8MHz

•

IDE Interfaces

♦

Provides one enhanced IDE controller (Compact Flash)

♦

Supports Ultra DMA 33/66/100 modes

♦

Supports ATAPI and DVD peripherals

♦

Supports IDE native and ATA compatibility modes

•

Floppy Disk Interface

♦

Supports one standard floppy disk drive interface

♦

Supports all standard PC/AT formats: 360KB, 1.2MB, 720KB, 1.44MB, 2.88MB

•

Parallel Port

♦

Provides a standard printer interface

♦

Supports IEEE standard 1284 protocols of EPP and ECP outputs

♦

Supports Bi-directional data lines

♦

Supports 16 byte FIFO for ECP mode

•

Serial Ports

♦

Four buffered serial ports with full handshaking

♦

Provides 16550-equivalent controllers, each with a built-in 16-byte FIFO buffer

♦

Supports full modem capability on all four ports

♦

Supports RS232, RS485, or RS422 operation on each port

♦

Supports programmable word length, stop bits, and parity

♦

Supports 16-bit programmable baud-rate generator and an interrupt generator

•

USB Ports

♦

Provides three root USB hubs

♦

Provides up to six USB ports

♦

Supports USB boot devices

♦

Supports USB v2.0 EHCI and UHCI v1.1

Содержание LittleBoard 735























































Результаты поиска

Содержание LittleBoard 735

Отзывы:

Похожие инструкции для LittleBoard 735

Бренды по названию

Популярные бренды

ADLINK Technology LittleBoard 735, Справочное руководство

Результаты поиска

Содержание LittleBoard 735

Отзывы:

Похожие инструкции для LittleBoard 735

Бренды по названию

Популярные бренды