ADLINK Technology LittleBoard 735 Скачать руководство пользователя | Manualshive

Страница: 48 / 54

background image

Chapter 4

BIOS Setup

42

Reference Manual

LittleBoard 735

5. Use the <Enter> key to select the screen menus listed in the Opening BIOS screen.

PCI-ISA Bridge Mapping

The LittleBoard 735 supports ISA bus based modules with an on-board PCI-ISA bridge. The PCI-ISA
bridge optionally maps the following resources to ISA based modules:

•

Memory

•

I/O Ports

•

IRQs

•

DMA Channels

The LittleBoard 735 system BIOS maps the above resources based on information provided in the BIOS

Setup screens. By default, only some of the I/O ports are mapped to ISA modules and any memory, IRQs or
DMA channels to be mapped to ISA modules must be explicitly specified by the user in the BIOS Setup

screens.

The IRQs and DMA channels are mapped with the “PCIPnP/IRQx” fields in BIOS setup (where x specifies
the IRQ number.) The IRQs 3, 4, 5, 7, 9, 10, 11, 14, and 15 can be mapped to ISA based modules by

changing the default setting for these IRQs from “Available” to “Reserved”.

ISA I/O ports, Memory, and DMA channels can be mapped to ISA modules on the “Boot/Boot Settings
Configuration” BIOS setup screen. Six I/O port “windows” and four memory “windows” are available for

mapping I/O Port or Memory regions to ISA modules by specifying the window length and base address.

By default, the following I/O port windows are mapped to ISA modules:

•

200-240h

•

240-260h

•

279h

•

300-340h

•

340-360h

•

A79h

By default, no memory windows are mapped to ISA modules.

Any of the DMA channels 0, 1, 2, 3, 5, 6, 7 can be mapped to ISA modules by changing the default setting
of “LPC Bridge” to “ISA Bridge”.

For example, to configure an ISA Soundblaster PnP card with resources 220/5/1/5 (Port/IRQ/DMA/DMA)

so that the Soundblaster would work in Windows XP, the following BIOS Setup changes would be required:

•

ISA I/O Ports – no changes necessary. 220h is already mapped to ISA by default.

•

IRQ – set IRQ5 to “Reserved” in BIOS Setup. See the paragraph above on mapping IRQs.

•

DMA1 and DMA5 – set DMA Channels 1 and 5 to “ISA Bridge” in BIOS Setup. See paragraph above
on mapping DMA Channels.

NOTE

The serial console port is not hardware protected, and is not listed in the COM table
within BIOS Setup. Diagnostic software that probes hardware addresses may cause a
loss or failure of the serial console functions.

NOTE

279h and A79 are the ISA PnP ports used by the BIOS and an OS that supports this
feature to recognize ISA PnP (Plug and Play) cards.

«
...
46
47
48
49
50
...
»

Содержание LittleBoard 735























































Отзывы:

Нет отзывов

Похожие инструкции для LittleBoard 735

Бренд: Abit Страницы: 104

Бренд: AOpen Страницы: 156

Бренд: Elitegroup Computer Systems Страницы: 82

Бренд: Giada Страницы: 2

EZ-USB HX2LP CY4606

Бренд: Cypress Страницы: 2

Бренд: Freescale Semiconductor Страницы: 16

PP-I7RS400 PURE PERFORMANCE II

Бренд: Sapphire Audio Страницы: 44

Бренд: MSI Страницы: 30

Бренд: IEI Technology Страницы: 162

H55M-LE - - 01-2010

Бренд: ASROCK Страницы: 181

Бренд: BESTEK Страницы: 13

Бренд: Linear Technology Страницы: 6

Бренд: Supero Страницы: 121

Бренд: Supermicro Страницы: 119

Бренд: Texas Instruments Страницы: 22

Бренд: DFI Страницы: 105

Бренд: ASROCK Страницы: 31

Бренд: Supermicro Страницы: 99

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды