Adeunis RF COMFORT MQTT Скачать руководство пользователя страница 24

Страница: 24 / 79

User Guide | COMFORT SERENITY MQTT | NB-IoT / LTE-Cat-M1

3.2. Estimated battery life with an LTE-Cat-M1
network connection

The table below has been estimated based on a product connected to an LTE-Cat-
M1 network with PSM (Power Saving Mode) support. Please note that the product's
battery life may vary depending on the selected operator.

Activated VOC Sensor, LEDs On

Sampling Frequency

Transmission Interval

Good Network
Autonomy (years)

Poor Network
Autonomy (years)

Every 10 minutes

2.8

< 1

Every 10 minutes

Every hour
(historization)

7.5

3.5

Every hour (default
product
configuration)

7.8

3.6

Every hour

Every 6 hours
(historization)

10.9

Disabled VOC sensor, LEDs On

Sampling Frequency

Transmission Interval

Good Network
Autonomy (years)

Poor Network
Autonomy (years)

Every 10 minutes

3.3

< 1

Every 10 minutes

Every hour
(historization)

12.4

4.5

Every hour (default
product
configuration)

13.1

4.6

Every hour

Every 6 hours
(historization)

> 15

Содержание COMFORT MQTT
















































































Результаты поиска

Содержание COMFORT MQTT

Отзывы:

Бренды по названию

Популярные бренды

Adeunis RF COMFORT MQTT, Руководство пользователя

Результаты поиска

Содержание COMFORT MQTT

Отзывы:

Бренды по названию

Популярные бренды