background image

13 

FL-Cool-200629-Rev003-UM-en 

Troubleshooting 

The table below shows the main problems that may occur during operation. 

FAULT 

CAUSES 

REMEDY 

The motor does not rotate and 
the worm shaft has stopped 

Check whether the machine is 
connected to the mains 

Connect it to the mains 

Check whether the connection 
of the three-phase plug + 
 neutral is correct. 

Ensure proper connection 

The worm shaft does not 
rotate 

Foreign object in the mincing 
section 

Remove the foreign object 

The running worm shaft makes 
noise 

The hand wheel is over-
tightened 

Slightly loosen the hand wheel 

The worm shaft is not latched 
into the slot 

Insert the worm shaft correctly 

Disc and blade are worn out 

Sharpen or replace the disc 
and blade 

Oil under the meat mincer 

Possible leak in the oil seal of 
the motor 

Replace the oil seal of the 
motor 

Display shows Pr1 

Error of room temperature 
probe 

Check the connection of the 
probe to the device. 
Check room temperature. 
Contact the service partner, if 
possible. 

Display shows Pr2 

Error of evaporator probe or 
error of condenser probe 

Check the connection of the 
probe to the device. 
Contact the service partner, if 
possible. 

Storage and Transport Conditions 

Keep all parts of the packaging in case you need to return the shipment to avoid possible damage 
during transportation. 

Warranty 

ADE will repair or replace this product if it has failed within 1 year from the date of purchase (proof of 
purchase is required) due to poor workmanship or defective material. 
All moving parts, such as cables, cross blades, perforated discs, etc., are excluded from this warranty. 
Warranty does not apply to normal appearance of usage or sign of wear or any damages caused by 
accidents or misuse. 
The warranty will not apply for devices that have been opened by unauthorised persons. 
This warranty agreement does not affect the customer's legal rights in any manner. 
The dealer from whom you purchased the machine is responsible for complaints. 

Disposal 

 

Waste electrical equipment do not belong in household waste. Please dispose of 
defective or old devices according to the legal and country-specific regulations!

 

 
 

 

Содержание FL82-Cool





















Отзывы: