ADB L-860 Скачать руководство пользователя страница 9

Страница: 9 / 29

L860 Elevated Low-Intensity Edge Light

Safety

2008 Siemens Airfield Solutions

96A0388B

Page

1-3

Issued 6/08

•

using materials or auxiliary equipment that are inappropriate or

incompatible with your ADB Airfield Solutions equipment

•

allowing unqualified personnel to perform any task

Read the installation section of all system component manuals before

installing your equipment. A thorough understanding of system

components and their requirements will help you install the system

safely and efficiently. See FAA Advisory Circular, AC 150/5340-30, for

Runway and Taxiway Edge Lighting Systems, and job site plans and

specifications for location and installation details.

WARNING

: Failure to follow these safety procedures can

result in personal injury or death.

•

Allow only qualified personnel to install ADB Airfield Solutions

and auxiliary equipment. Use only approved equipment. Using

unapproved equipment in an approved system may void agency

approvals.

•

Make sure all equipment is rated and approved for the

environment in which you are using it.

•

Follow all instructions for installing components and accessories.

•

Install all electrical connections to local code.

•

Use only electrical wire of sufficient gauge and insulation to

handle the rated current demand. All wiring must meet local

codes.

•

Route electrical wiring along a protected path. Make sure they

will not be damaged by moving equipment.

•

Protect components from damage, wear, and harsh environment

conditions.

•

Allow ample room for maintenance, panel accessibility, and cover

removal.

•

Protect equipment with safety devices as specified by applicable

safety regulations.

•

If safety devices must be removed for installation, install them

immediately after the work is completed and check them for

proper functioning.

4. Intended Use

(contd.)

Installation

Содержание L-860






























Результаты поиска

Содержание L-860

Отзывы:

Похожие инструкции для L-860

Бренды по названию

Популярные бренды

ADB L-860, Руководство пользователя

Результаты поиска

Содержание L-860

Отзывы:

Похожие инструкции для L-860

Бренды по названию

Популярные бренды