ADB L-860 Скачать руководство пользователя страница 28

Страница: 28 / 29

L860 Elevated Low-Intensity Edge Light

Parts

2008 Siemens Airfield Solutions

96A0388B

Page

7-4

Issued 6/08

NOTES:
1.
2.
3.

Configure 44a6886 optical assemblies to /1XXX for heated versions.

White LED'S (3W) use the 1000mA, Red and Green (1W) use 400mA (6477)PWR supply.

44A6334-7

ELIL GLASSWARE ASSY FAA ELIL RED GREEN

44A6334-8

ELIL GLASSWARE ASSY FAA ELIL RED

44A6334-9

ELIL GLASSWARE ASSY FAA ELIL GREEN-OBSCURED

44A6477-1-0400

PCB ASSY,LED UNIV AC PS, 400mA, W/BRKT

44A6576-40

CORDSET ASSY 95-260VAC & 120VAC

44A6886-0300

ELIL OPTICAL ASSEMBLY, RED/GREEN, BI-DIR

44A6886-0410

L-860 OPTICAL MT. RED OMNI WITH RESISTOR

44A6886-0510

L-860 OPTICAL MT. RED WITH RESISTOR

64A0173-8

1/4-20 X 1/2 HX HD

66A0015/29

3/8 SS FLAT WASHER

88A2146

CASTING, LED ELEVATED LIGHT HOUSING

ETES WIRE TIE

WIRE TIE .19W X .045T X 2 MIN LG.

BI-DIRECTIONAL and
UNI-DIRECTIONAL
ASSEMBLY SHOWN

Orient glassware assembly integral to led
lamp color assembly of LED mount

EXAMPLE 1:
Red glass with red LED

EXAMPLE 2:
Green glass with green LED, obscured
glass with no LED.

OMNI-DIRECTIONAL
ASSEMBLY SHOWN

64A0957-06

6-32 PAN HD PHIL W/CAPTURED EXT STAR WASHER

67A0033

THERMAL JOINT COMPOUND

67A0048

ANTI-SEIZE COMPOUND

RM0512

POLYESTER FILM TAPE

Note 1

Equipment not Shown but Required

Frangible Coupling

62B0073 w/1-1/2 -12UNF Thread (shown)
61A0281 w/special 2 NPT
61A0350 w/2-11 TPI (ICAO)

1/4-20 Hex Head Bolt, 64A0173 (3 ea. on housing, 1 ea. on frangible coupling)

Column

67A0007-2 for 14 inch OAH, 2-inch coupling only
67A0007-3 for 14 inch OAH, 1-1/2 coupling
67A0007-13 for 14 inch OAH, 1-1/2 and 2-inch coupling

88A2146
Housing

44A6576-40

Power Cordset Assembly

Note 3

Note 2

White LED Assembly

44A6662-071E w/o heater
44A6662-271E w/heater (arctic kit)

Glassware Assembly

44A6334-4 FAA
44A6334-5 ICAO

Glassware

63A1117W (FAA)
63A1117C (ICAO)

Figure 7-2 ELIL L860 Elevated LED Fixture Parts

Содержание L-860






























Результаты поиска

Содержание L-860

Отзывы:

Похожие инструкции для L-860

Бренды по названию

Популярные бренды

ADB L-860, Руководство пользователя

Результаты поиска

Содержание L-860

Отзывы:

Похожие инструкции для L-860

Бренды по названию

Популярные бренды