ADB L-860 Скачать руководство пользователя страница 25

Страница: 25 / 29

L860 Elevated Low-Intensity Edge Light

Parts

2008 Siemens Airfield Solutions

96A0388B

Page

7-1

Issued 6/08

Section 7

Parts

To order parts, call ADB Airfield Solutions Customer Service or your

local representative. Use this four-column parts list, and the

accompanying illustration, to identify and order parts correctly.

Using the Illustrated Parts List

This subsection describes how to use the illustrated parts list covered

later in this section. It does not provide the actual parts list.

The Part Number column gives the ADB Airfield Solutions part

number.

The Description column gives the part name, as well as its

dimensions and other characteristics when appropriate. Indentions

show the relationships between assemblies, subassemblies, and

parts.

Part Number

Description

Quantity

Note

xxxxxxxx Assembly

1 A

xxxxxxxx Part

xxxxxxxx

Part or Assembly

xxxxxxxx Assembly

NOTE A

The Quantity column contains the quantity required per unit,

assembly, or subassembly. The code AR (As Required) is used if the

part number is a bulk item ordered in quantities or if the quantity per

assembly depends on the product version or model.

The Note column contains letters that refer to notes at the end of

each parts list. Notes contain special ordering or product/part version

information.

Introduction

Содержание L-860






























Результаты поиска

Содержание L-860

Отзывы:

Похожие инструкции для L-860

Бренды по названию

Популярные бренды

ADB L-860, Руководство пользователя

Результаты поиска

Содержание L-860

Отзывы:

Похожие инструкции для L-860

Бренды по названию

Популярные бренды