ADB L-860 Скачать руководство пользователя страница 21

Страница: 21 / 29

L860 Elevated Low-Intensity Edge Light

Troubleshooting

2008 Siemens Airfield Solutions

96A0388B

Page

5-1

Issued 6/08

Section 5

Troubleshooting

WARNING:

Allow only qualified personnel to perform the

following tasks. Observe and follow the safety instructions

in this document and all other related documentation.

WARNING:

De-energize the circuit and lock out the circuit

or regulator so that the circuit cannot be energized by

remote means before attempting to service the fixture.

This section contains troubleshooting information for the L-860 light

fixture. This information covers only the most common problems

that you may encounter. If you cannot solve the problem with the

information given here, contact your local ADB Airfield Solutions

representative for help.

Refer below for troubleshooting procedures for the L-860 LED

elevated light.

Problem Possible

Cause Corrective

Action

1. LED not lighting

Defective electronic module

Loose wire connections

Deteriorated wire insulation or

voltage too low

Moisture present in fixture

Replace the electronic module.

Tighten wire connections.

Replace wires or correct input voltage.

Open and dry the fixture. Inspect the

glassware for cracks. Replace the

electronic module, seals, and damaged

glassware assembly. Refer to the

procedure under

LED Electronic Module

Replacement

in the

Repair

section.

2. LED too dim

Dirty Glassware or voltage too low

Service life of LED exceeded

NOTE: Refer to

Expected LED

Life

under

Specifications

in the

Description

section.

Clean the glass lens or correct input

voltage.

Replace the electronic module.

3. Ice forming on lens

Defective or missing arctic kit

Remove the glassware assembly and

check to see if heating element is

installed. If missing or defective install

new arctic kit. See Spare Parts List in

Section 7.

Introduction

Troubleshooting

Procedures

Содержание L-860






























Результаты поиска

Содержание L-860

Отзывы:

Похожие инструкции для L-860

Бренды по названию

Популярные бренды

ADB L-860, Руководство пользователя

Результаты поиска

Содержание L-860

Отзывы:

Похожие инструкции для L-860

Бренды по названию

Популярные бренды