ADB Safegate RELIANCE Omni 1-Dome Скачать руководство пользователя страница 37

Страница: 37 / 66

6.4.6 Assembling a 8

‑

inch Fixture

Replacement

1. Carefully clean all contact surfaces of the light fixture and of the housing.
2. Install a new O-ring gasket on the bottom cover.

Figure 10: Replacing Cover/Inner Cover O-ring Gasket

A = O-Ring seal
B = Screw Driver Pry Slot

Important

The O-ring gasket must be changed each time the light fixture is disassembled.

3. Connect LED assembly with converter by pressing connector on.

Important

Make sure that the cable is correctly installed according to the pictures below. Refer to

Figure 11

a) Connect the LED board cable. Note the orientation and alignment of the cable. Connect the LED board cable

connector to the Supply Terminal of the converter in the housing. Note the orientation and alignment of the LED

board cables.

Note

Before closing the light fixture, it is important to make sure the O-ring is placed correctly in the groove of the

bottom cover to prepare the light fixture for water tightness checks and use in the airfield. For more

information, refer to

Figure 21

NOTICE

Make sure that the LED cable is connected to the LED B-channel.

b) Place the top cover over the bottom cover, align A and B sides on the top cover with the corresponding sides on the

bottom cover.

UM-5073, Rev. 1.0, 2021/07/13

Содержание RELIANCE Omni 1-Dome


























































Результаты поиска

Содержание RELIANCE Omni 1-Dome

Отзывы:

Похожие инструкции для RELIANCE Omni 1-Dome

Бренды по названию

Популярные бренды

ADB Safegate RELIANCE Omni 1-Dome, Руководство пользователя

Результаты поиска

Содержание RELIANCE Omni 1-Dome

Отзывы:

Похожие инструкции для RELIANCE Omni 1-Dome

Бренды по названию

Популярные бренды