ADB Safegate RELIANCE Omni 1-Dome Скачать руководство пользователя страница 55

Страница: 55 / 66

8.0 Spare Parts

Spare parts are available for RELIANCE and RELIANCE IQ inset light fixtures. For more information, see

www.adbsafegate.com

and the spare part lists, or contact ADB SAFEGATE for assistance.

8.1 Ordering Code Taxiway Edge omnidirectional Light

The illustration below clarifies the structure of the ordering code for the RELIANCE Taxiway Edge Omni with one dome.

Ordering Code

Primary Standard

1 = FAA / ICAO

Market-Specific

0 = None

Dimensions

1 = 8-inch

Prism

S = 1 standard dome

Beam Orientation

3 = Omnidirectional

Toe-in

N = Not applicable

Colors (Side 1)

B = Blue

Y = Yellow

Colors (Side 2)

N = Not applicable

Power and Monitoring

S = 2.8 - 6.6 A, Non-Monitoring

M = 2.8 - 6.6 A, Monitoring

P = 2.8 - 6.6 A / 2A IQ0 (IQ disabled)

Q = 2.8 - 6.6 A / 2A IQ1 (IQ enabled)

Connector and Cable

1 = 1 x Style 6 2-pole plug, 2 individual wires

5 = 1 x Flat 3-pole plug, 3 individual wires

Options

0 = None

Version Control

1 = First edition

Notes

Option 1 covers other compliance: MOS.

Power only

With fail-open

The IQ-functionality allows control and monitoring of the RELIANCE IQ. IQ1

fittings are pre-configured for the specific position at delivery. This
function is disabled in IQ0 fittings but could be enabled in a later state.

IQ light fixtures are only available as one connector option.

French 3-pin plug

UM-5073, Rev. 1.0, 2021/07/13

Содержание RELIANCE Omni 1-Dome


























































Результаты поиска

Содержание RELIANCE Omni 1-Dome

Отзывы:

Похожие инструкции для RELIANCE Omni 1-Dome

Бренды по названию

Популярные бренды

ADB Safegate RELIANCE Omni 1-Dome, Руководство пользователя

Результаты поиска

Содержание RELIANCE Omni 1-Dome

Отзывы:

Похожие инструкции для RELIANCE Omni 1-Dome

Бренды по названию

Популярные бренды