Ada Platinum Elite, Руководство по установке

Страница: 6 / 48

5. Mounting the Control Box Assembly
6. Connecting the Zone Dampers
7. Connecting the AC
Ÿ
Mount the Control Box Assembly in the roof space in a location central to all of the Zone
Dampers, ideally near a ceiling access panel.
Ÿ
Mount in a well ventilated area and as far away from the roof surface as possible.
Ÿ
The Control Box Assembly should be screwed to the roof structure at a level to provide
easy access for the connection of cables.
DO NOT cover the Control Box Assembly with insulation
DO NOT mount below water heaters.
DO NOT mount near or below water pipes.
DO NOT mount near power cables or other sources of electrical noise.
Ÿ
Plug in the DC power supply to the Modbus Adapter socket and connect the twin plug IEC
power cord to the Control Box Assembly and the DC Power Supply.
Ÿ
Plug in the Coms Cable from the wall mounted Tablet.
Ÿ
Ÿ
The last step is to plug in the power cord to a standard power outlet. The power outlet
must be fitted by a licenced electrician.
DO NOT power up the Control Box Assembly until all connections are made.
Ÿ
Plug in the Zone Damper cables to the Control Box, starting at position number 1 and
continuing with adjacent consecutive sockets.
Ÿ
Ÿ
Record the position and size of each Zone Damper on the record sheet in the back of this
manual, noting which, if any, are designated as Relief Zones.
It is recommended to use an off-the-shelf cable tester to check the Coms Cable prior to
installation and in particular, after being pulled through a wall cavity.
Only Zone Damper cables and joiners (if necessary) supplied by Air Diffusion Agencies
must be used. It is recommended to use an off-the-shelf cable tester to check Zone
Damper cables prior to installation.
more information r
All AC systems must be fully commissioned and tested with a standard AC Wall Controller
connected to the AC Indoor Unit to complete necessary field settings and to confirm the AC
runs normally.
efer to the relevant brand AC
Commissioning Notes provided and the Platinum Elite Gateway instruction sheet. In
general, to connect the AC to the Zone Control System:
Ideally, the standard AC Wall Controller should be mounted away from the
Platinum Elite Tablet, ie. in a discrete but accessible location such as a utility room, a
cupboard or in the roof space near a ceiling access panel. This allows for easy access should
the AC unit require adjustments to the factory settings by qualified personnel. The system
will use the default return air temperature of the AC Indoor Unit as the reference
temperature for AC control. For
MOUNTING THE CONTROL BOX CONNECTING THE AC
INSTALLATION MANUAL 4 5
240VAC
Power Cord
Control Box Assembly
Zone Damper Cables
Mounting Screw
Coms Cable (to Tablet)
24VDC
Power
Supply
From 24VDC
Power Supply
AC Link Cable
to Gateway
Ÿ
as far from the roof surface as possible and
Ÿ
Ÿ
Ensure power is off and refer to the relevant brand AC Control Wiring Diagrams to connect
the Gateway. All Gateways require the
2-core AC Link Cable (PETCW) for the A+B-
connection to the Control Box Assembly.
Ÿ
It is recommended to mount the Gateway
vertically, using the pull-out mounting tabs provided.
Ÿ
Refer to DIP switch settings (if applicable) on the AC Control Wiring Diagrams.
After completing wiring and setting the DIP switches, power up the system. AC Unit,
Platinum Elite Gateway and Platinum Elite Zone Control System can be powered up at the
same time, but if powered up separately, ensure AC Unit and Platinum Elite Gateway are
on before the Platinum Elite Zone Control System.
The system should automatically detect the Platinum Elite Gateway during the setup
process. (If the Gateway is added after the initial setup process, on the Zone Setup screen
it will be necessary to perform a ‘Recheck’ to allow the Gateway to be detected.) Follow
the onscreen prompts to complete the AC setup.
supplied
LED light
indicates
power
Mounting Screw
AC Link Cable to
Control Box Assembly
AC Link Cable to
Control Box Assembly
A+B-
Platinum Elite
Gateway
Platinum Elite
Gateway
UP UP