Active Technologies AT-1120 Скачать руководство пользователя

Страница: 34 / 41

AT-1120 User Guide and Specifications - 33 -

www.activetechnologies.it

15.

Wire controls and indicators from the input/output terminals

datai2c0

datai2c1, datai2c2,

datai2c3, datai2c4, datai2c5, readdataI2c,startrdi2c, startwri2c, reset_in, trig_in,

trig_out, clkenable, clocksel

and

lockedfast .

16.

Wire the 40MHz Onboard Clock to the clock loop.

17.

Add another Timed Loop as shown in the figure below and right-click to open the LabView
palette. Select the

FPGA I/O palette

and add an

I/O node

18.

Wire the datadac_ch0_in0_..datadac_ch0_in15 connectors as in the picture above.

19.

Wire the

IO Module Clock 0

to the clock loop.

20.

Right-click to open the LabView palette. Select the

Memory & FIFO palette

and add a

Memory Method node.

Right-click on the Memory method, Select

Memory>>Memory1

21.

Left-click on the Memory1 Memory Method and select the

Read

method. Insert a new shift

Содержание AT-1120










































Результаты поиска

Содержание AT-1120

Отзывы:

Похожие инструкции для AT-1120

Бренды по названию

Популярные бренды

Active Technologies AT-1120, Руководство пользователя

Результаты поиска

Содержание AT-1120

Отзывы:

Похожие инструкции для AT-1120

Бренды по названию

Популярные бренды