ACTi A713 Скачать руководство пользователя

Страница: 93 / 115

⚫

Light On Mode (Built-in IR LED Modules Only)

In this mode, IR LED lights will always be on.

⚫

Light Off Mode (Built-in IR LED Modules Only)

In this mode, IR LED lights will always be off.

Day/Night Threshold

This item is for users to set when the camera should switch from day mode to

night mode or vice versa. The camera will sense the surrounding brightness,

and the threshold value stands for the level of the light. Once the camera

detects the light level reaches the set threshold, the camera will automatically

switch to Day/Night Mode. The range of the level is from 0 to 10, (darker = 0;

brighter = 10).

⚫

Night Mode to Day Mode

The lower the value, the earlier the camera switches to Day mode. The

default value is 7.

⚫

Day Mode to Night Mode

The higher the value, the earlier the camera switches to Night mode.

The default value is 3.

NOTE:

Equipped with different CMOS sensors, the time the camera

switches to Day/Night mode may also vary from models to models even

if the threshold is set to the same value.

IR Light Compensation

With the IR Light Compensation function, the camera can prevent the center

object close to the camera from being too bright when IR LED lights are turned

on.

Содержание A713




















































































































Результаты поиска

Содержание A713

Отзывы:

Похожие инструкции для A713

Бренды по названию

Популярные бренды

ACTi A713, Руководство по прошивке

Результаты поиска

Содержание A713

Отзывы:

Похожие инструкции для A713

Бренды по названию

Популярные бренды