Actel ProASIC3/E Скачать руководство пользователя страница 43

Страница: 43 / 106

Step 2 – Perform Pre-Synthesis Simulation

ProASIC3/E Starter Kit User’s Guide and Tutorial

Copy Waveforms

It is possible to copy and paste sections of waveforms onto (overwrite) or into (insert) any signal in the diagram.

To copy and paste waveform sections:

Select the names of the required signals. If no signals are selected, the Block Copy command selects all the signals
in the diagram.

Select the

Edit

Block Copy Waveforms

menu option (choose to select all waveforms, if necessary). This opens the

Block Copy Waveforms dialog box (

Figure 7-14 on page 43

) with the selected signals displayed in the Change

Waveform Destination list box.

Figure 7-14. Block Copy Waveforms Dialog Box

Enter the values that define the copy and paste.

Select either

Time

Clock

cycle for the base units of the dialog.

Remember the following:

When copying only signals (no clocks), time is the default base unit of the dialog.

When copying part of a clock, it is best to choose a clock cycles base unit and choose the copied clock as the reference
clock.

If you select time when copying clocks, the end_time minus the start_time must equal an integral number of clock
periods, and the place_at time must be at the same clock period offset as the start_time.

Start

and

End

define the times of the block copy.

Place At

is the time at which the block will be pasted.

The

Insert

and

Overwrite

radio buttons determine whether the paste block is inserted into the existing waveforms

or overwrites those waveforms.

Содержание ProASIC3/E











































































































Результаты поиска

Содержание ProASIC3/E

Отзывы:

Actel ProASIC3/E, Руководство пользователя, Страница: 43 / 106

Результаты поиска

Содержание ProASIC3/E

Отзывы: