Actel ProASIC3/E Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 106

Actel ProASIC3/E Скачать руководство пользователя страница 33

Design Implementation

ProASIC3/E Starter Kit User’s Guide and Tutorial

33

Design Implementation

During design implementation, Actel Designer places-and-routes the design.

Place-and-Route

Start Designer from Libero IDE to place-and-route the design.

Timing Simulation

Perform timing simulation on the design after place-and-route in Designer. Timing simulation requires information
extracted and back-annotated from Designer.

Optional Tools

The tools listed in

provide optional functions that are not required in a basic design. Use these tools to

perform static timing analysis, power analysis, customize I/O placements and attributes, and view the netlist. After
place-and-route, perform the post-layout (timing) simulation.

For more information on the tools described in the above section, refer to the Designer User’s Guide.

Programming

Program the device with programming software and hardware from Actel or a supported third party programming
system. Refer to the Designer User’s Guide, Silicon Sculptor User’s Guide, and FlashPro User’s Guide for information
about programming an Actel device. These guides can be found at

http://www.actel.com/techdocs/manuals/

System Verification

Use the Logic Navigator tool to perform system verification on a programmed device.

Table 6-1 · Designer User Tools

Designer User Tools

User Tool Function

Timer

Static timing analysis

SmartPower

Power analysis

ChipEdit

Customize I/O and logic macro
placements

PinEdit

Customize I/O placements and
attributes

Netlist Viewer

View your netlist and trace paths

«
...
31
32
33
34
35
...
»

Содержание ProASIC3/E











































































































Отзывы:

Нет отзывов