manualshive.com logo in svg

Actel ProASIC3/E, Руководство пользователя, Страница: 14 / 106

Поделиться
Скачать
Actel ProASIC3/E Скачать руководство пользователя страница 14

Hardware Components

14

ProASIC3/E Starter Kit User’s Guide and Tutorial

Procedure for Rev3 Boards

To determine if the board is a Rev3 board: 

A Rev3 Board is recognized by examining the front of the board and looking for the part number just beneath the large 
Actel corporate logo on the board top silk-screen. The part number will be A3PE-

A3P-EVAL-BRD1

 followed by 

REV3

.

To chain Rev3 boards together: 

All boards from the board nearest the FlashPro3 programmer should have the shunt that is placed by default on pins 3 
and 4 of the J5 header moved to connect pins 1 and 2. On the board and schematic this is labeled quite clearly as 

CHAIN

 (pins 1 and 2) and 

LAST DEVICE (DEFAULT)

 (pins 3 and 4).   Only the very last board in the chain 

should have the shunt remaining across pins 3 and 4 of the J5 connector.

Note that if there is only one board in the chain then it, by definition, is the last board and should have the shunt at J5 
connecting pins 3 and 4. This is why this position is labeled as the DEFAULT position for a typical customer with a 
single starter kit board. 

Procedure for Rev2 Boards, With and Without Rework

To determine if the board is a Rev2 board:

A Rev2 board is indicated by a red power LED in the upper right corner of the board and a part number underneath the 
Actel corporate logo on the board top silk-screen. The part number will be “A3PE-A3P-EVAL-BRD1”.   No additional 
text will follow the board number. If the board has been reworked to force it to become equivalent to a Rev3 board, it will 
contain a green wire on the top side of the board. If it does not contain green wire, it is an original Rev2.

To chain Rev2 boards together:

If reworked, treat it as Rev3 in the previous section. If not reworked, then chaining of the boards cannot be done. The 
shunt on J5 must be removed for any programming to take place.

Procedure for Rev1 Boards

To determine if the board is a Rev1 board: 

A Rev1 Board is indicated by no red power LED in the upper right corner of the board. The part number on the board 
top silk-screen is 

A3PE-EVAL-BRD600

.

Note:

Rev1 boards should not be used with this tutorial guide or with design files included with this Starter Kit as the 
schematics are incompatible with current commercial boards.

V

PUMP

 Connections When Chaining Boards Together

When these boards are connected via a connection from J2 of one board to J1 of another board, V

PUMP

 will be 

connected from one board to another. When powering on one board with a connector in place, notice that the 1.5 V, 1.8 
V, 2.5 V, and 3.3 V LEDs will light on the board to which no power has been applied. The FPGA on that board, if it is 
programmed, will start operating. This is clearly an inappropriate situation for a large chain of boards. This is caused by 
having the JP48 connector for supplying V

PUMP

 from the board connected on other boards in the chain, as V

PUMP

 is 

itself connected to the 3.3 V supply output that is used to generate the other FPGA voltages on a board. To prevent 
V

PUMP

 from being used as the source of a 3.3 V supply, you should remove the shunt that is in place on the JP48 

connector to force JP48 to be open-circuit. To prevent loss of the shunt, it may be safely stored on the J12 header for the 
daughter card power supply as it is impossible to cause a short by joining any adjacent pins.

Содержание ProASIC3/E











































































































Отзывы:

Нет отзывов