INDUSTRIAL I/O PACK SERIES ACPC8625 CompactPCI BUS CARRIER BOARD
___________________________________________________________________________________________
- 13 -
Radiated Emissions..................... Meets or exceeds European
Norm EN50081-1 for class A
equipment.
APPENDIX
CABLE: MODEL 5028-187 (SCSI-2 to Flat Ribbon, Shielded)
Type: Round shielded cable, 50-wires (SCSI-2 male connector at
one end and a flat female ribbon connector at the other end).
The cable length is 2 meters (6.56 feet). This shielded cable is
recommended for all I/O applications (both digital I/O and
precision analog I/O).
Application: Used to connect Model 5025-552 termination panel to
the TRANS-C200 Transition Module. The transition module
then connects to all four IP module slots to the rear of the
ACPC8625 (Slots A-D).
Length: Standard lenght is 2 meters (6.56 feet). Consult factory for
other length. It is recommended that this length be kept to a
minimum to reduce noise and power loss.
Cable: 50 conductors, 28 AWG on 0.050 inch centers (permits
mass termination for IDC connectors), foil/braided shield inside
a PVC jacket.
Connectors: (One End): SCSI-2, 50-pin male connector with
backshell and spring latch hardware. (Other End): IDC, 50-pin
female connector with strain relief.
Keying: The SCSI-2 connector has a “D Shell” and the IDC
connector has a polarizing key to prevent improper installation.
Schematic and Physical Attributes: See Drawing 4501-758.
Electrical Specifications: 30 VAC per UL and CSA (SCSI-2
connector spec.’s). 1 Amp maximum at 50% energized
(SCSI-2 connector spec.’s).
Operating Temperature: -20
°
C to +80
°
C.
Storage Temperature: -40
°
C to +85
°
C.
Shipping Weight: 1.0 pound (0.5Kg), packed.
TERMINATION PANEL: MODEL 5025-552
Type: Termination Panel For Carrier Boards
Application: To connect field I/O signals to the Industrial I/O Pack
(IP). Termination Panel: Acromag Part 4001-040 (Phoenix
Contact Type FLKM 50). The 5025-552 termination panel
facilitates the connection of up to 50 field I/O signals and
connects to the TRANS-C200 transition module via a cable
(Model 5028-187). Field signals are accessed via screw terminal
strips. The terminal strip markings on the termination panel (1-
50) correspond to P2 (pins 1-50) on the Industrial I/O Pack (IP).
Each Industrial I/O Pack (IP) has its own unique P2 pin
assignments. Refer to the IP module manual for correct wiring
connections to the termination panel.
Schematic and Physical Attributes: See Drawing 4501-464.
Field Wiring: 50-position terminal blocks with screw clamps. Wire
range 12 to 26 AWG.
Connections to TRANS-C200 Transition Module: P1, 50-pin male
header with strain relief ejectors. Use Acromag 5028-187 cable
to connect panel to TRANS-C200 transition module. Keep
cable as short as possible to reduce noise and power loss.
Mounting: Termination panel is snapped on the DIN mounting rail.
Printed Circuit Board: Military grade FR-4 epoxy glass circuit board,
0.063 inches thick.
Operating Temperature: -40
°
C to +100
°
C.
Storage Temperature: -40
°
C to +100
°
C.
Shipping Weight: 1.25 pounds (0.6kg) packed.
CompactPCI TRANSITION MODULE: MODEL TRANS-C200
Type: Transition module for ACPC8625 board.
Application: To repeat field I/O signals of IP modules A through D
for rear exit from CompactPCI card cages. This module is
available for use in card cages which provide rear exit for I/O
connections via 80 mm wide transition modules (transition
modules can only be used in card cages specifically designed
for them). It is a double-height (6U), single-slot module with front
panel hardware adhering to the CompactPCI bus mechanical
dimensions and IEEE Standard (1101.11-1998), for 80 mm
depth. Connects to Acromag termination panel 5025-552 from
the rear of the card cage, and to ACPC8625 boards within card
cage, via connectors P4 and P5.
Schematic and Physical Attributes: See Drawing 4501-791.
Electrical Specifications: 30 VAC per UL and CSA (SCSI-2
connector spec.’s). 1 Amp maximum at 50% energized
(SCSI-2 connector spec.’s).
Field Wiring: Four SCSI-2, 50-pin female connectors (AMP
787082-5 or equivalent) employing latch blocks and 30 micron
gold in the mating area (per MIL-G-45204, Type II, Grade C).
Connects to Acromag termination panel 5025-552 from the rear
of the card cage via round shielded cable (Model 5028-187).
Connections to ACPC8625: Connections are made though the PC
board connectors P4 and P5 (right-angle female connector, 110
contacts with upper shield. The transition module plugs directly
behind the ACPC8625 board into the CompactPCI bus
backplane within the card cage system.
Mounting: Transition module is inserted into a 6U-size, 80 mm
width slot at the rear of the CompactPCI bus card cage.
(Directly behind ACPC8625 board)
Printed Circuit Board: Eight-layer, military-grade FR-4 epoxy glass
circuit board, 0.063 inches thick.
Operating Temperature: -40
°
C to +85
°
C.
Storage Temperature: -40
°
C to +85
°
C.
Shipping Weight: 1.25 pounds (0.6Kg) packed.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
