background image

DC Inverter 

X-Series

 for R410A Unitary Split Air Conditioner 

30

 

No. 

Error code 

Error 

26 

e3 

Low pressure sensor error 

27 

C4 

ODU jumper cap error 

4.3 Unit Maintenance 

. Only professionals are allowed to carry on daily maintenance.

. Before contacting any wire, make sure power is cut off.

. Do not let any inflammable objects near the unit.

. Do not use organic solvent to clean the air conditioner.

. If you need to replace a component, please ask a professional to repair with a

component supplied by the original manufacturer so as to ensure the unit’s quality.

. Improper operation may get the unit broken, hit by electric shock or cause fire.

. Do not make the air conditioner wet or electric shock may be lead, Ensure that the

air conditioner will not be cleaned by water rinsing under any circumstance.

. Before cleaning, please make sure the unit is stopped. Cut the circuit breaker and

remove the power socket, otherwise, electric shock may occur.

. Do not wash the air conditioner with water, otherwise fire hazard or electric shock

may occur.

. When cleaning the filter, please be careful of your steps. If you need to work high

above the ground, please be extremely careful.

4.3.1 Heat Exchanger of Outdoor Unit 

Conduct cleaning for the heat exchanger of outdoor unit periodically, clean it once 

at least in every two months. Clean the dust and sundries on the surface of the heat 
exchanger with dust collector and nylon brush, if there’s compressed air source; use 
the compressed air to blow the dust on the surface of the heat exchanger. Don’t use tap 
water for cleaning.   

4.3.2 Drainage Pipe 

Periodically check if the drainage pipe is blocked to smooth the condensate water. 

4.3.3 Notices at the Beginning of the Using Season 

(1) Check if the air inlet/outlet of the units are blocked.
(2) Check if the ground connection is reliable.

Содержание AULD36W2/A-D










































Отзывы: