Ace Heating Solutions Mini-Pack, Инструкция по эксплуатации и техническому обслуживанию

Страница: 26 / 100

A
JAX
B
OILER
I
NC.
- A
CE
B
OILER
I
NC.
W
ARNING
PRODUCT
SAFETY NOTICE
AJAX BOILER AND WATER HEATER PRODUCTS OPERATE AT HIGH TEMPERATURE AND PRESSURES
• Before using this product, read and understand instructions. Save these instructions for future use.
• Before servicing, to prevent serious burns or injury, the boiler and water heater products must be cooled to less than
80°F (27°C) and the pressure must be 0 psi (0 bar).
• Turn off the electrical power before making electrical connections to prevent electrical shock.
• These products must be placed in a controlled location where untrained or unqualifi ed personnel cannot access the
operating or safety controls, must not be able to come in contact with high temperature or high pressure parts and must
not perform maintenance or demolition work.
• All work performed must be by qualifi ed properly equipped personnel trained in the proper application, installation, and
maintenance or demolition of plumbing, steam, and electrical equipment and/or systems in accordance with all
applicable codes and ordinances.
• Ajax Boilers and Water Heaters are complete package units with safety and operating controls and are constructed with
non ASBESTOS materials. Any replacement gaskets, refractory, insulation, etc used must not contain Asbestos.
• No additional insulation is required on the Boilers and Water Heaters.
• Additions or replacement of insulation on any connecting pipes or accessories to the Boilers and/or Water Heaters must
be of “NON-ASBESTOS” and contain only non-hazardous materials.
• Crystalline Silica, a material known to cause cancer, may be encapsulated in some refractory or insulation materials
and must be handled only by authorized trained personnel. Crystalline Silica as used is encapsulated and is not harm
full in this form. Care must be taken during removal or replacement of refractory or insulation to remove it in bulk
form and avoid generation or inhalation of dust. Removal must be properly performed by trained, qualifi ed and
equipped personnel. This is also true of Asbestos not contained in Ajax products but may be otherwise contained in
replacement materials or parts, in connecting piping or other nearby products.
• All safety and operating controls must be set within the specifi ed operating limits and tested periodically to assure proper
operation. All limit and operating controls must be installed in series on the boiler.
• Connect drain pipes to a safe drain to prevent serious personal injury from relief valve discharge and or from boiler blow
down discharge.
• After installation, check for proper operation of all limit and operating controls before leaving the site.
• Perform scheduled and annual inspections including checking Controls for proper calibration and performance.
Failure to follow these warnings, to allow access by unauthorized persons and the use of non-properly trained and
equipped personnel in the operation, service, modifi cation, removal or demolition of these products or replacement
of parts with non-authorized factory non-asbestos materials could cause damage, personal injury or death.
2701 South Harbor Blvd.
Santa Ana, California 92704
United States
Tel. (714) 437-9050
Fax (714) 437-9060
http://www.ajaxboiler.com
mail@ajaxboiler.com
A
CE
Heating Solutions, LLC
2701 S. H
ARBOR
B
LVD
. • S
ANTA
A
NA
, CA 92704
P
HONE
: (714) 540-2230 • FAX: (714) 540-2239
www.aceheatingllc.com
Ace Heating Solutions, LLC
November 2014 ace
ACE BOILER AND WATER HEATER PRODUCTS OPERATE AT HIGH TEMPERATURE AND PRESSURES
• Before using this product, read and understand instructions. Save these instructions for future use.
• Before servicing, to prevent serious burns or injury, the boiler and water heater products must be cooled to less than
80°F (27°C) and the pressure must be 0 psi (0 bar).
• Turn off the electrical power before making electrical connections to prevent electrical shock.
• These products must be placed in a controlled location where untrained or unqualified personnel cannot access the
operating or safety controls, must not be able to come in contact with high temperature or high pressure parts and must
not perform maintenance or demolition work.
• All work performed must be by qualified properly equipped personnel trained in the proper application, installation, and
maintenance or demolition of plumbing, steam, and electrical equipment and/or systems in accordance with all
applicable codes and ordinances.
• ACE Boilers and Water Heaters are complete package units with safety and operating controls and are constructed with
non ASBESTOS materials. Any replacement gaskets, refractory, insulation, etc used must not contain Asbestos.
• No additional insulation is required on the Boilers and Water Heaters.
• Additions or replacement of insulation on any connecting pipes or accessories to the Boilers and/or Water Heaters must
be of “NON-ASBESTOS” and contain only non-hazardous materials.
• Crystalline Silica, a material known to cause cancer, may be encapsulated in some refractory or insulation materials
and must be handled only by authorized trained personnel. Crystalline Silica as used is encapsulated and is not harm
full in this form. Care must be taken during removal or replacement of refractory or insulation to remove it in bulk
form and avoid generation or inhalation of dust. Removal must be properly performed by trained, qualified and
equipped personnel. This is also true of Asbestos not contained in ACE products but may be otherwise contained in
replacement materials or parts, in connecting piping or other nearby products.
• All safety and operating controls must be set within the specified operating limits and tested periodically to assure proper
operation. All limit and operating controls must be installed in series on the boiler.
• Connect drain pipes to a safe drain to prevent serious personal injury from relief valve discharge and or from boiler blow
down discharge.
• After installation, check for proper operation of all limit and operating controls before leaving the site.
• Perform scheduled and annual inspections including checking Controls for proper calibration and performance.
Failure to follow these warnings, to allow access by unauthorized persons and the use of non-properly trained and
equipped personnel in the operation, service, modification, removal or demolition of these products or replacement
of parts with non-authorized factory non-asbestos materials could cause damage, personal injury or death.