background image

Installation & Operation Manual

 - Model VTS 

Contents of this Manual are Subject to Change Without Notification

 

Page 5 

SECTION 2 - SPECIFICATIONS 

PERFORMANCE 

 

Accuracy  +/- 5% of reading or 5 CFM, whichever is greater 

Min Operating Pressure  Reference Section 2.1 

Airflow Range  Reference Section 2.1 

ENVIRONMENTAL 

 

Temperature  Airstream: -20 to 165 deg. F  

Ambient:   -20 to 125 deg. F 
Storage:     -40 to 165 deg. F 

Humidity  0 to 90% non-condensing 

TRANSMITTER ELECTRICAL 

 

Power Supply  24 VAC +/- 20% 50/60 Hz, 4 VA max (8.5 VA max with remote monitor) 

  24 VDC +/- 10% 1.5 W max (3.5 W max with remote monitor) 

Output Signal  Software Configurable; 0-20mA, 4-20mA, 0-10V, 2-10V, 0-5V, or 1-5V 

  12-bit Resolution capable of driving 1K-ohm load 

Configuration Port  USB 2.0, Isolated, C Type Connector 

Power Source Switch  Operational Position: Draws power from 24V input terminal block 

Nonoperational Position: Draws power from 5V USB port (Use for configuration only)  

BACnet MS/TP 

(Optional)

  EIA 485 2-wire BACnet MS/TP, Galvanically Isolated 
  Data Rates 9600, 19200, 38400, 57600, 76800 and 115200 
  1/8 Unit Load Receiver Input Impedance 
  Network bias and EOL Termination not provided within the Transmitter 

Remote Monitor 

Sold 

Separately

 

LCD, 2 lines x 8 characters with white LED backlight 

 

Includes USB Configuration Port and Factory Cable 

Terminal Plugs  3-position, vertical pluggable, screw on top, wire size 12-30 AWG 

EMC 

Safety 

EN 61326-1:2013, 2014/35/EU (LVD), 2014/30/EU (EMC) 
EN 61010-1:2010 

 

FCC Part 15

 

 

This equipment has been tested and found to comply with the limits for a Class A digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference when the equipment is operated in a commercial 
environment. This equipment generates, uses, and can radiate radio frequency energy and, if 
not installed and used in accordance with the instruction manual, may cause harmful 
interference to radio communications. Operation of this equipment in a residential area is 
likely to cause harmful interference in which case the user will be required to correct the 

interference at the user’s own expe

nse.  This Class A digital apparatus meets all requirements 

of the Canadian Interference-Causing Equipment Regulations. 

 

 

 

Model Code Material 

Designator 

(2) 304SS 

(3) 316SS 

(4) Aluminum 

Housing 

304L SS 

316L SS 

Alum. 5052-H32 

Compression Section 

304L SS 

316L SS 

Alum. 5052-H32 

Static Regain Section 

304L SS 

316L SS 

Alum. 5052-H32 

End Plate 

304L SS 

316L SS 

Glv. Steel 

Vortex Sensors 

Polycarbonate 

UL94-VO 

Polycarbonate 

UL94-VO 

Polycarbonate 

UL94-VO 

Sensor Tubing 

Polyurethane, 

Ether-based 

Polyurethane, 

Ether-based 

Polyurethane, 

Ether-based 

MATERIALS OF CONSTRUCTION (In Airstream)

 

Содержание VTS


























Отзывы: