Accurate Technology 150 Скачать руководство пользователя страница 43

Страница: 43 / 48

ProScale M150, M250 with LCD Digital Displays

Page 43 of 48

Programming Summary

Factory

Parameter

Function

Default

THIS SYSTEM

Pr0

Reading Direction

______

Pr1

Segment Offset

1 - On

______

Pr2

High Speed ReadHead

0 - Off

______

Pr3

Zero, Offset Entry

1 - Enable

______

Pr4

Display Resolution

1 - Normal

______

Pr5

mm or cm

0 - mm

______

Pr6

Fractions, mm, in

0 - all

______

Pr7

Scaling

1.0000 (none)

______

Pr8

Auto off

15 - 15 min.

______

Pr9

Auxiliary Keypad

7 - all keys

______

Pr10

Offset Addition

0 - disabled

______

Pr11

Offset Addition 1

1.000 Inch

______

Pr12

Offset Addition 2

1.500 Inch

______

Pr13

Offset Addition 3

2.000 Inch

______

Pr14

Output Mode

0 - off

______

Pr15

Output Polarity

0 – Normally Open ______

Pr16

Lower Limit

0.000

______

Pr17

Upper Limit

5.000 Inch

______

Pr18

Drift Tolerance

.010 Inch

______

Pr19

Auto Monitor ON

0 - disabled

______

Pr20

Auto Monitor OFF

0 - disabled

______

Pr21

Auto Monitor Distance

.500 Inch

______

Pr22

Backlight On

4 - Always

______

Pr23

FUTURE FEATURE

______

Pr24

RF Display Address

0 – Off

______

Pr25

RF System ID

______

Pr26

Noise Suppression

0 – Minimum

______

Pr27 *

Accuracy Comp. Enable 1 – ON

______

Pr28 *

Compensation Multiple

5 – 5 in.

______

* Pr27 and Pr28 are only operational with a special version of Firmware.

ProScale Display units that support the

Compensation

feature have a “C” at

the end of the firmware revision ID. (The Firmware Version is momentarily

displayed on power-up).

Pressing and holding the

ON/OFF

key and

MODE

key for 10 seconds

with power off

will perform a full segment LCD test AND set all

Programming Parameters to factory defaults.

Note: Defaulting the display to factory defaults will NOT erase the

compensation table.

Содержание 150

















































Результаты поиска

Содержание 150

Отзывы:

Похожие инструкции для 150

Бренды по названию

Популярные бренды

Accurate Technology 150, Руководство пользователя

Результаты поиска

Содержание 150

Отзывы:

Похожие инструкции для 150

Бренды по названию

Популярные бренды