Accurate Technology 150 Скачать руководство пользователя страница 33

Страница: 33 / 48

ProScale M150, M250 with LCD Digital Displays

Page 33 of 48

Primary Key Functions

ON/OFF

Momentarily pressing the

ON/OFF

key will cause the Display to turn on or off.

The Firmware Version is momentarily displayed on power-up. While on, if no

key presses or positional changes occur within 15 minutes*, the Display will

automatically turn itself off to conserve battery life. While off, if a position

change is detected (larger than .05mm or .002in), the Display will

automatically turn itself on with no loss of measurement information.

*(Programming Parameter Pr8)

Pressing and holding the

ON/OFF

key for 5 seconds while the Display is

turned on will display internal battery voltage.

MODE

The ProScale can display measurement information in Inch or Metric. To

change the display mode, momentarily press the

MODE

key. With each key

press, the Display will cycle through decimal inches, fractional inches* (1/16),

(1/32), (1/64) and metric (mm or cm based on setting of Programming

Parameter Pr5). * If enabled by Programming Parameter Pr6.

When the Display is in a decimal mode (mm, cm or in) it will auto-range to

the next resolution if the value is displayable in the next range. This allows

the Display to be used with Mitutoyo Digimatic® products in inch mode or

different resolutions other than 2 decimal places.

When the Display is in 1/16 or 1/32 inch fraction mode, a series of “bars” in

the upper right corner of the LCD each

represent 1/64th of an inch

measurement. (ie. When in 1/16 inch mode and three bars are showing, the

measurement displayed is rounded

down

to closest 1/16 inch and each

illuminated bar indicates an additional 1/64 of an inch (“heavy”)

measurement.) For better resolution switch to 1/32 or 1/64 fraction mode.

For the best resolution switch to a decimal mode.

When the measurement is greater than + 99 63/64 inches, a

+100

+200

will show in the upper right portion of the LCD to indicate this amount must

be added to the displayed reading. ie: if the measurement is 154 5/8 inches,

54 5/8 and +100 will be displayed on the LCD. If the measurement is -307

23/64 inches, - 7 23/64 , +100 and +200 will be displayed on the LCD.

The Resolution of the Display can be set for

NORMAL

: (.01mm or .001in),

REDUCED

: (.1mm or .01in) or

INCREASED

: (.01mm or .0005in).

(Programming Parameter Pr4.)

Содержание 150

















































Результаты поиска

Содержание 150

Отзывы:

Похожие инструкции для 150

Бренды по названию

Популярные бренды

Accurate Technology 150, Руководство пользователя

Результаты поиска

Содержание 150

Отзывы:

Похожие инструкции для 150

Бренды по названию

Популярные бренды