background image

11

www.acclaimlighting.com

Operation

Addressing fixtures

Dyna Graze HO Exterior DMX fixtures have no external controls and instead rely on RDM 
(Remote Device Management) for all configuration via the DMX interface. This allows 
multiple devices to be configured either before or after installation. 
Various third party DMX/RDM tools are available; Acclaim Lighting particularly recommend 
the Swisson XMT-350 for this task.

To address fixtures using the Swisson XMT-350

1  Connect the XMT-350 to the DMX input line of either a single fixture or multiple fixtures in 

a pre-arranged daisy chain configuration.

2  Power on the fixture(s) and the XMT-350.
3  On the XMT-350, press the 

MODE

 button, then use the arrow buttons to highlight the 

RDM

 

function and press the   button to select. The XMT-350 will search for RDM devices and 
after a short while the XMT-350 will display a list of all located fixtures:

The fixture that is highlighted within the list should begin flashing its emitters to identify 
itself.

4  On the XMT-350, press the right arrow button to change to the 

PATCH

 tab:

5  If necessary, use the up/down buttons to choose an alternative fixture. 
6  Press the    button to set the address for the currently highlighted fixture:

7  Use the up/down buttons to set the required DMX address and then press the    button 

to store it within the fixture.

8  The highlight will automatically move to the next fixture so that you can address it. 

Repeat steps 5 to 7 until all fixtures are addressed.       

Note: DMX addresses shown in brackets, e.g. 
(001), have been temporarily assigned by the 
XMT-350, but are not yet stored within the 
fixture(s).   

Содержание Dyna Graze HO Exterior DMX





















Отзывы: