manualshive.com logo in svg

Accedian EtherNID GE, Руководство администратора

Поделиться
Скачать
Accedian EtherNID GE Скачать руководство пользователя страница 44

3: Management and configuration

Management bridge

44

6. Delete any existing interfaces with the following commands:

interface delete Management

interface delete Network

7. The Network port of EtherNID #1 will be used for the in-band management. Configure the 

Network port with the following command:

interface add net1-10 type vlan vlan1-id 10 port Network address 

192.168.1.253 netmask 255.255.255.0

8. Repeat configuration steps 1. to 7. on EtherNID #3 using the following settings when 

defining the new interface:

interface add net3-10 type vlan vlan1-id 10 port Network address 

192.168.1.252 netmask 255.255.255.0

9. Repeat configuration steps 1. to 6. on EtherNID #2. 

10. Execute the following commands to add three interfaces on EtherNID #2:

interface add mgmt type standard port Management

interface add cli10 type vlan vlan1-id 10 port Client

interface add net10 type vlan vlan1-id 10 port Network

The interface 'mgmt' will be used to connect to the management bridge. The other two 
interfaces will be used to access the other two EtherNIDs remotely.

11. Next, create the bridge interface. Execute the following command to bridge all three 

interfaces together for access using the Management port.

interface add Bridge type bridge sub-intf mgmt,cli10,net10 address 

192.168.1.254 netmask 255.255.255.0

12. Connect the Management port of EtherNID #2 to the private network.

13. Open a web browser on a computer connected to the private network and enter the 

address 

192.168.1.254 

to reach the management web interface on EtherNID #2.

14. Connect the Client port of EtherNID #2 to the Network port of EtherNID #3.

15. Connect the Network port of EtherNID #2 to the Network port of EtherNID #1.

16. Open a web browser and enter the address 

192.168.1.254 

to reach the management web 

interface on EtherNID #2.

17. Open a second web browser and enter the address 

192.168.1.253 

to reach the 

management web interface on EtherNID #1.

18. Open a third web browser and enter the address 

192.168.1.252 

to reach the 

management web interface on EtherNID #3.

Содержание EtherNID GE







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды